Index Terms - User’s Manual

3
- 3-point placement[1]
- 3-POINT START[1]
4
- 4-point placement[1]
- 4-POINT START[1]
- Perforated cutting line[1]
- Tiled output[1]
A
- Adobe Illustrator[1][2][3]
- Alignment tool[1]
- Amount of blade extension[1]
- Applying from the memory[1]
- Area[1]
- Automatic aligning[1][2][3][4]
B
- Blade Force[1][2]
- Blade holder[1][2]
- Blade holder cap[1]
- Blade offset[1][2]
- Blade Protector[1][2]
C
- Canceling[1]
- Carriage LED Lamp[1]
- Cleaning[1]
- Connecting Multiple Units[1][2][3][4][5][6]
- Consumable products[1]
- Contrast[1]
- CorelDRAW[1][2]
- CROP ADJ.[1]
- Crop Marks[1]
- Cursor keys[1]
- Cut data[1][2][3]
- Cut setting[1]
- CutStudio[1][2][3]
- Cutter[1][2]
- Cutting[1][2][3][4]
- Cutting area[1][2]
- Cutting carriage[1]
- Cutting conditions[1]
- Cutting coordinate origin[1]
- Cutting coordinates[1]
- Cutting-in amount[1]
- Cutting Lines[1][2][3][4]
- Cutting off material[1]
- Cutting perforated lines[1]
- Cutting position adjustment[1]
- Cutting Preview[1]
- Cutting Speed[1][2][3]
D
- Data output[1]
- Display[1]
- Distance between crop marks[1]
E
- EDGE[1]
- ENTER key[1]
- Ethernet connector[1]
- EXTEND[1]
F
- FACTORY DEFAULT[1]
- FIRMWARE[1]
- Flat material[1][2][3]
- Force[1]
- FORCE key[1]
G
- Grit pattern[1]
- Grit roller[1]
- Guide line[1][2]
H
- Half-cut[1][2][3]
- Help[1][2]
I
- Image Darkness[1]
- Inner margin[1][2]
- Interface[1]
K
- Knife guide[1]
L
- Language[1]
- LENGTH[1]
- Lift up[1]
- Loading lever[1]
- Loading material[1][2][3][4]
M
- Manual mode[1][2][3][4]
- Margin[1]
- Material feeding[1]
- Material with perforations for sprocket feed[1][2]
- Memory[1]
- MENU key[1]
- Misalignment[1]
- MODEL[1]
- Multiple cutting[1]
O
- Offset[1][2]
- Operation panel[1]
- Origin[1]
- ORIGIN key[1]
- Output size[1]
- Output-start location[1]
- Over cut[1]
- OVERLAP[1]
- Overlap cutting[1]
P
- Palette[1][2]
- PAUSE[1]
- PAUSE key[1]
- PEN FORCE slider[1]
- Perforated cutting conditions[1][2][3]
- Perforation[1][2][3]
- PIECE[1]
- Pinch roller[1][2]
- Power button[1]
- Power cord connector[1]
- PRE-FEED[1]
- Print & Cut[1][2][3][4][5]
- Print & Cut data[1][2]
- Printing[1]
- Printing position adjustment[1]
R
- Removing the material[1]
- REPLACE TO TOOL[1]
- Replacing the Blade[1]
- Replot[1]
- ROLL[1]
- Roller base[1]
- Roll material[1][2][3]
- ROTAT[1]
S
- Screen brightness[1]
- SELECT SHEET[1][2]
- Sensor Mode[1][2][3][4][5][6][7][8][9]
- SERIAL No.[1]
- Setting the alignment method[1]
- Setup[1]
- Smoothing[1]
- SPEED[1]
- SYSTEM INFO.[1]
T
- TEST CUT[1]
- TEST key[1]
- Test pattern[1]
- Tile size[1]
- Tool marks[1]
- Tool Mode[1][2]
U
- Uninstall[1]
- UNIT[1]
- Unusable material[1]
- UPSPEED[1]
- USB connector[1]
V
- VACCUMFAN[1]
- Vertical writing font[1]
W
- WIDTH[1]