Jump to index list
User's Manual
  • 2
  • A
    • Activity LED[1]
    • Advanced maintenance[1]
    • Amount of cleaning liquid remaining[1]
    • Amount of ink remaining[1]
    • Apron[1]
    • Automatic maintenance[1]
    • Automatic Sub Power On[1]
    • Automatic Sub Power On Settings[1]
  • B
  • C
    • CALIBRATION[1][2]
    • Canceling[1]
    • Cartridge slots[1]
    • Circulation When Sub Power Automatically Turns On[1]
    • CLEANING TEST PRINT[1][2][3]
    • Cleaning When Sub Power Automatically Turns On[1]
    • Collective Settings[1]
    • Color Theme[1]
    • Control box[1]
    • CROP-CUT ADJ.[1][2][3][4][5]
    • Crop Mark Detection Sensitivity[1]
    • Crop marks[1]
    • CUT CONFIG[1][2][3]
    • Cutting[1]
    • Cutting Distance Correction[1]
    • Cutting Force[1]
    • Cutting line misalignment[1][2][3]
    • CUTTING PRIOR[1]
    • Cutting speed[1]
    • Cutting with crop marks[1]
  • D
  • E
    • EMPTY MODE[1]
    • End caps[1]
    • Ethernet connector[1]
    • Exception Dates[1]
    • Extended Dryer[1]
  • F
  • G
  • H
  • I
    • Initialization[1]
    • Ink Mixing Notification[1]
    • Ink renewal[1]
    • Ink Type[1]
    • IP address[1]
  • J
  • L
    • LANGUAGE[1]
    • Left cover[1]
    • Left media holder[1]
    • Length[1]
    • Light choke cleaning[1]
    • Loading lever (front)[1]
    • Loading lever (rear)[1]
  • M
    • MAC address[1]
    • Machine information[1]
    • Main power switch[1]
    • Manual cleaning[1]
    • MANUAL switch[1]
    • Media clamp[1]
    • Media Clamp Placement Notification[1]
    • Media condition[1]
    • Media Gap Adjustment[1]
    • Media heating system[1]
    • Media holders[1]
    • Media information[1]
    • MEDIA RELEASE[1][2]
    • Media stays[1]
    • Medium cleaning[1]
    • Menu list[1]
    • Middle Pinch Auto Raise/Lower[1]
    • Middle Pinch Roller Placement Notification[1]
    • Model[1]
    • Motorized media holder[1]
    • Multi sensor[1][2]
    • Multi Sensor Adjustment[1]
  • N
  • O
    • Obtain IP address automatically[1]
    • Operation panel[1]
    • Over cut[1]
  • P
  • R
    • Registered media[1][2][3]
    • Regular maintenance[1]
    • Remaining media[1]
    • Remaining Media Management[1]
    • REPLACE KNIFE[1]
    • Replace the cleaning liquid pouch.[1]
    • Replacing consumable parts[1]
    • Resuming[1]
    • Returning settings to factory defaults[1]
    • Right cover[1]
    • Rise Movement Speed[1]
    • Roll media[1][2][3]
  • S
    • Screen Brightness[1]
    • Screen Operation Sound[1]
    • Separating knife[1][2][3]
    • Serial[1]
    • Set the left edge of the printing area within the area specified by the rollers.[1]
    • Set the right edge of the printing area within the area specified by the rollers.[1]
    • Setup[1][2][3][4][5][6]
    • Shafts[1][2]
    • Sheet Cutting[1]
    • Sheet media[1][2][3]
    • SHEET REMAIN, PRINT MEMO[1]
    • SLEEP[1]
    • Sleep mode[1][2]
    • Software Error[1]
    • Status bar[1]
    • Status LED[1]
    • Sub carriage[1]
    • SUBNET MASK[1]
    • Sub power[1]
    • System information[1]
  • T
    • Take-up unit[1][2][3][4]
    • Temperature[1]
    • TEST PRINT[1]
    • TEST PRINT CUT ONLY[1]
    • TEST PRINT NOZZLE MASK[1]
    • TEST PRINT POS[1]
    • The media could not be detected automatically. Manually set the printing area.[1]
    • Time[1]
    • TO CANCEL, HOLD DOWN PAUSE KEY[1]
    • Turning the power off[1]
    • Turning the power on[1]
  • U
    • Unit setting[1]
  • V
  • W