Jump to index list
User's Manual
  • A
    • Activity LED[1]
    • Amount of blade extension[1]
    • Amount of ink remaining[1]
    • Apron[1]
  • B
  • C
    • Cancel Output[1]
    • Cancel Setup[1]
    • CIRCULATE INK[1]
    • Cleaning[1]
    • Cleaning during Printing[1]
    • Cleaning liquid pouch replacement[1]
    • Cleaning liquid slot[1]
    • Control box[1]
    • Crop & Cut Position Adjustment[1]
    • CROP-CUT ADJ.[1][2]
    • Crop Mark Detection Sensitivity[1]
    • Cutting[1]
    • Cutting carriage[1]
    • Cutting Distance Correction[1]
    • Cutting Force[1]
    • CUTTING PRIOR[1]
    • Cutting Speed[1]
    • Cutting with crop marks[1]
  • D
  • E
    • End caps[1]
    • Ethernet connector[1]
    • Extended Dryer[1]
  • F
  • G
    • Grit patterns[1]
    • Grit roller[1]
  • H
  • I
    • Initialization[1]
    • Ink Mixing Notification[1]
    • Ink pouch replacement[1]
    • Ink renewal[1]
    • Ink Renewal Inside Damper[1]
    • Ink slots[1]
    • Ink Type[1]
    • Install the cleaning liquid pouch.[1]
    • IP address[1]
  • L
    • Language[1][2]
    • Left cover[1]
    • Left media holder[1]
    • Left pinch roller[1]
    • Length[1]
    • List of Media Settings[1]
    • Loading lever (front)[1]
    • Loading lever (rear)[1]
    • Loose Winding[1]
    • Low Temperature Error[1]
  • M
    • MAC address[1]
    • Machine Information[1]
    • Main power switch[1]
    • Manual cleaning[1]
    • MANUAL switch[1]
    • Media clamp[1]
    • Media Clamp Placement Notification[1]
    • Media Gap Adjustment[1][2]
    • Media heating system[1]
    • Media holders[1]
    • Media information[1]
    • Media stays[1]
    • Media Sticking Prevention[1]
    • Media Suction Force[1]
    • Medium cleaning[1]
    • Menu[1]
    • Middle Pinch Auto Raise/Lower[1]
    • Middle pinch roller[1]
    • Middle Pinch Roller Placement Notification[1]
    • MODEL[1]
    • Motor Error[1]
    • Motorized media holder[1]
    • Move[1]
    • Multi sensor[1]
    • Multi Sensor Adjustment[1]
  • N
    • Network Settings Settings[1]
    • Normal cleaning[1]
    • Notifications[1]
    • Notifications On/Off[1]
    • Nozzle Drop-out Test[1]
    • Nozzle mask[1]
    • Nozzle Mask Test[1]
  • O
    • Obtain IP Address Automatically[1]
    • Operation panel[1][2]
    • Over cut[1]
  • P
    • Paper tube[1]
    • Pausing[1][2]
    • Perforated Sheet Cutting[1]
    • Pinch roller[1]
    • Platen[1]
    • Power-cord connector[1]
    • Powerful cleaning[1]
    • Prefeeding at Output
    • Print & Cut Position Adjustment[1]
    • PRINT-CUT ADJ.[1]
    • Print-head carriage[1]
    • Print Head Dry-out Error[1]
    • Print Head Height[1]
    • Print heater[1][2][3][4][5]
    • Printing[1]
    • Printing and cutting[1]
    • Printing Area (Width)[1][2][3]
    • Printing Movement Range[1]
    • Printing Remaining Media Amount[1]
    • Print light[1][2]
    • PRINT ONLY[1]
    • Pump Stop Error[1]
  • R
    • Remaining Media Management[1][2]
    • REPLACE KNIFE[1]
    • Replace the cleaning liquid pouch.[1]
    • Resuming[1]
    • Retainer[1]
    • Returning settings to factory defaults[1]
    • Right cover[1]
    • Right pinch roller[1]
    • Rise Movement Speed[1]
    • Roll media[1][2][3]
  • S
  • T
    • Take-up[1]
    • Take-up Direction[1][2]
    • Take-up Method[1][2]
    • Take-up unit[1][2]
    • Temperature[1]
    • Tension Winding[1]
    • TEST PRINT POS[1]
    • The media could not be detected automatically. Manually set the printing area.[1][2][3]
    • Time[1]
    • Tray pad[1]
  • U
    • Unit setting[1]
  • W
    • When output, cleaning, and other operations are completed, discard the discharged fluid.[1]
    • Wiper[1][2]
    • Wiper tray[1][2]