Printer Controls

Sets the printer control method during printing.

Item				Description	Refer to
General				Sets the sheet cut-off after output and page space.
	Cut Sheet after Output			Cuts the sheet after output. Default value: Off	Cutting the Media after Output
	Use Custom Settings			Changes Page Space. Default value: Off	Setting the Space to the Next Printing Start Location
		Page Space		Sets the space to the next printing start location.	Setting the Space to the Next Printing Start Location
Feed Calibration Controls				Configures the settings in order to alleviate the horizontal bands that occur during printing. Default value: Use Printer Settings	Determining How to Alleviate Horizontal Bands
	Use Default Media Settings			Printing is performed with the recommended values for the media selected with Media Type under Quality Settings.
	Use Custom Settings			Printing is performed with the values set in this window.
	Use Printer Settings			Printing is performed with the settings configured on the printer.
		Feed Calibration		If you select Use Custom Settings, enter the Feed Calibration.
Rotary Controls				The optional rotary axis unit is used to print on a cylindrical object (media) while it is rotated. Click Automatic Calculation to calculate the number of nozzles (the feed length) to use.	Printing Using the Rotary Axis Unit
	Nozzle Amount to Use in Printing
		Automatic Calculation
Other Controls				Specifies the control method for Vacuum Power, Dry Time, and Head Height.
	Use Default Media Settings			Printing is performed with the recommended values for the media selected with Media Type under Quality Settings.
	Use Custom Settings			Printing is performed using the Vacuum Power, Dry Time, and Head Height which are set in this window.
	Use Printer Settings			Printing is performed with the settings configured on the printer.
		Vacuum Power		Sets the intensity of the vacuum that holds the media flat on the platen. This can be set when [Use Custom Settings] is selected.	Using Media That Wrinkles Easily/Does Not Move Smoothly
			Normal
			Strong
		Dry Time		Sets the time (in minutes) to wait before printing the next page or cutting. This can be set when [Use Custom Settings] is selected.	Setting the Drying Time after Printing
		Head Height		Sets the height of the print head. This can be set when [Use Custom Settings] is selected. Normally do not change this setting.	Adjusting Print Head Height to Match Media Thickness
Heater Controls				Specifies the Heater Controls setting method. Default value: Use Printer Settings	Setting the Heater/Dryer Temperature
	Use Default Media Settings			Printing is performed using the settings for each media that were configured with VersaWorks.
	Use Custom Settings			Sets the temperature for Pre Heater, Print Heater, and Dryer.
		Pre Heater
		Print Heater
		Dryer
	Use Printer Settings			Printing is performed with the settings configured on the printer.
UV Lamp Control				Specifies the UV lamp control method.
	Operation Mode			Specifies the target for irradiation by the UV lamp.
		Print		This is the default setting. Printing and UV irradiation are performed.
		UV Illumination Only		You can configure the settings so that only the UV illumination matching that performed during printing is performed again after printing.	Performing Only UV Lamp Illumination
		Scan Speed		This can be set when UV Illumination Only is selected.
	Change UV Lamp Illumination Intensity			Adjusts the illumination intensity of the printer's UV lamp.	Reducing the UV Lamp Illumination Intensity
		Illumination Intensity			Reducing the UV Lamp Illumination Intensity
Print Size Correction				You can correct a shifted printing result by adjusting the horizontal and vertical sizes of the printing data. If you enter the measured sizes (the actual print size) and the expected sizes (the size to be printed), the correction factors can be automatically calculated and easily set. You can also enter the correction factors directly.	Correcting the Dimensions in the Printing Results
	Horizontal			Enter the correction factors directly.
	Vertical			Enter the correction factors directly.
	Correction Calculator			Click this button to display the Correction Calculator window.
		Correction in X-Direction		Sets the correction factor for the horizontal direction. Can be set within a range of -5.00% to +5.00%.
			Expected Size	Enter the size to be printed.
			Measured Size	Enter the measured size of the printing result.
			Correction Factor	This is automatically calculated on the basis of the entered values.
		Correction in Y-Direction		Sets the correction factor for the vertical direction. Can be set within a range of -5.00% to +5.00%.
			Expected Size	Enter the size to be printed.
			Measured Size	Enter the measured size of the printing result.
			Correction Factor	This is automatically calculated on the basis of the entered values.

Feedback

Was this information helpful?

	1	2	3	4	5
NO						YES

Any additional feedback to help us improve.