Jump to index list
User's Manual
  • A
    • Activity LED[1]
    • Amount of blade extension[1]
    • Amount of ink/cleaning liquid remaining[1]
    • Apron[1]
    • Automatic Feeding after Printing[1]
  • B
  • C
  • D
  • E
    • Ethernet connector[1]
  • F
    • Feed correction[1]
    • Firmware version[1]
    • Flushing[1]
    • Flushing cover[1]
    • Flushing sponge[1]
    • Front cover[1]
  • G
    • Grit patterns[1]
    • Grit roller[1]
  • H
  • I
    • Initialization[1]
    • Ink circulation[1]
    • Ink Expiration Date Notification[1]
    • Ink Mixing Notification[1]
    • Ink renewal[1]
    • Ink replacement method[1]
    • Ink Type[1]
    • Install the cleaning liquid cartridge.[1]
    • IP address[1]
  • L
    • Language[1][2]
    • Left cover (bottom)[1]
    • Left cover (top)[1]
    • Left pinch roller[1]
    • Length[1]
    • Light Choke Cleaning[1]
    • List of Media Settings[1]
    • Loading lever (front)[1]
    • Loading lever (rear)[1]
  • M
    • MAC address[1]
    • Machine information[1]
    • Main power switch[1]
    • Manual cleaning[1]
    • Media clamp[1]
    • Media Clamp Placement Notification[1]
    • Media Gap Adjustment[1]
    • Media heating system[1]
    • Media holders[1]
    • Media information[1]
    • Media stays[1]
    • Media Suction Force[1]
    • Medium cleaning[1]
    • Menu[1]
    • Middle Pinch Auto Raise/Lower[1]
    • Middle pinch roller[1]
    • Middle Pinch Roller Placement Notification[1]
    • Model[1]
    • Move[1]
  • N
    • Network[1]
    • Normal cleaning[1]
    • Notifications[1]
    • Notifications On/Off[1]
    • Nozzle Drop-out Test[1]
    • Nozzle mask[1]
    • Nozzle Mask Test[1]
  • O
    • Obtain IP address automatically[1]
    • Operation panel[1][2]
    • Over cut[1]
  • P
    • Pausing[1][2]
    • Perforated Sheet Cutting[1]
    • Pinch roller[1]
    • Platen[1]
    • Power-cord connector[1]
    • Powerful cleaning[1][2]
    • Prefeeding at Output
    • Print head cap[1]
    • Print-head carriage[1]
    • Print Head Height[1]
    • Print heater[1][2][3]
    • Printing[1]
    • Printing and cutting[1]
    • Printing Area (Width)[1][2][3]
    • Printing Movement Range[1]
    • Printing Remaining Media Amount[1]
    • Priority for Cutting Settings[1]
  • R
    • Remaining Media Management[1][2]
    • REPLACE KNIFE[1]
    • Resuming[1]
    • Retainer[1]
    • Returning settings to factory defaults[1]
    • Right cover[1]
    • Right pinch roller[1]
    • Rise Movement Speed[1]
    • Roll media[1][2][3]
  • S
    • Screen brightness[1]
    • Screen Operation Sound[1]
    • Sedimentation[1]
    • Separating knife[1][2][3]
    • Serial[1]
    • Set the left edge of the printing area within the area specified by the rollers.[1][2][3]
    • Set the right edge of the printing area within the area specified by the rollers.[1][2][3]
    • Setup[1][2][3][4][5]
    • Shafts[1]
    • Sheet Cutting[1][2]
    • Sheet media[1][2][3]
    • SLEEP[1]
    • Sleep mode[1]
    • Software Error[1]
    • Software RIP Priority[1]
    • Standby Heater Temperature[1]
    • Start-up cleaning[1]
    • Status bar[1]
    • Status LED[1]
    • SUBNET MASK[1]
    • Sub power[1]
    • System information[1]
  • T
    • Temperature[1]
    • Test Cut[1][2]
    • TEST PRINT POS[1]
    • The media could not be detected automatically. Manually set the printing area.[1][2][3]
    • The time for flushing sponge replacement has arrived.[1]
    • Time[1]
    • Turning the power off[1]
    • Turning the power on[1]
  • U
    • Uneven color issues[1]
    • Unit setting[1]
  • W
    • When output, cleaning, and other operations are completed, discard the discharged fluid.[1]
    • Wiper[1][2][3]
    • Wiper cleaner[1]
    • Wiper cleaner cover[1]