Index Terms

A
- Activity LED[1]
- Advanced maintenance[1]
- Amount of blade extension[1]
- Apron[1]
- AUTO MIDDLE PINCH[1]
- AVOIDING DRY-UP TURN POWER OFF[1]
B
- BASE POINT[1]
- BASE POINT light[1]
- Blade[1]
- Blade protector[1]
- Bluetooth[1][2]
- BUSY light[1]
C
- CALIBRATION[1][2]
- CANCELED FOR PUMP PROTECTION[1]
- Canceling[1]
- CHANGE CL-LIQUID FOR WIPER[1]
- Cleaning slot[1]
- CLOCK[1]
- Consumable parts[1]
- Consumable products[1]
- CROP-CUT ADJ.[1][2]
- Crop marks[1]
- CROPSENS CALIB SENS LEVEL[1][2]
- CROP SENSOR ADJ.[1]
- Cursor[1]
- Cursor keys[1]
- CUT CONFIG[1][2][3][4][5]
- Cutting[1]
- Cutting carriage[1]
- Cutting output[1]
- CUTTING PRIOR[1]
- Cutting with crop marks[1][2]
D
- DATE[1]
- Direction mark[1]
- Display screen[1]
- DRAIN BOTTLE[1][2]
- DRYER[1][2][3][4][5]
- DRYING TIME PRINT[1]
- DRY TIME P&C[1]
E
- EDGE DETECTION[1]
- EMPTY DRAIN BOTTLE[1]
- ENTER key[1]
- ENTER mark[1]
- Ethernet connector[1]
F
- FACTORY DEFAULT[1]
- FEED FOR DRY, P&C[1]
- FEED FOR DRY PRINT[1]
- FORCE[1]
- Front cover[1]
- FULL WIDTH S[1]
- FUNCTION, SHEET CUT[1]
- FUNCTION key[1]
- Function menu[1]
G
- GATEWAY ADDR.[1]
- Grit patterns[1]
- Grit roller[1]
H
- HEAD HEIGHT[1][2][3][4]
- HEATER CONFIG[1][2][3][4]
- HEATER light[1]
I
- INK[1]
- Ink pouches[1]
- Ink pouch replacement[1]
- Ink slot cover[1]
- Ink slots[1]
- IP ADDRESS[1]
L
- LANGUAGE[1]
- Language and unit menu[1]
- Left cover[1]
- Left pinch roller[1]
- LENGTH UNIT[1]
- Loading lever (front)[1]
- Loading lever (rear)[1]
M
- M.PINCH CHECK[1]
- MAC ADDRESS[1]
- Main menu[1]
- Main power switch[1]
- Manual cleaning[1][2]
- Maximum printing area
  - Maximum printing area[1]
- Media clamp[1]
- MEDIA GAP ADJ. DETAIL SETTING[1][2]
- MEDIA GAP ADJ. SIMPLE SETTING[1]
- Media heating system[1]
- Media holders[1]
- MEDIA RELEASE[1]
- MEDIA SETTING[1][2][3][4]
- Media stays[1]
- Medium cleaning[1]
- MENU key[1]
- Middle pinch roller[1]
- MODEL[1]
- MOTOR ERROR TURN POWER OFF[1]
N
- NETWORK[1]
- Normal cleaning[1][2][3][4]
- Nozzle mask[1]
O
- OFFSET[1]
- Operation panel[1]
- Over cut[1]
P
- PAUSE key[1]
- Pausing[1]
- PERIODIC CL.[1]
- Pinch roller[1]
- Platen[1]
- POWER[1]
- Power-cord connector[1]
- Powerful cleaning[1]
- PREFEED[1][2]
- PREHEATING[1]
- Present value[1]
- PRESET, LOAD[1]
- PRESET, SAVE[1]
- PRINT (print heater)[1][2][3][4]
- PRINT-CUT ADJ.[1]
- Print-head carriage[1]
- Print heater[1]
- Printing[1]
- Printing and cutting[1]
- Printing and cutting output[1]
- Printing output[1]
- PRINT LIGHT[1][2]
- PRINT ONLY[1]
R
- Regular Maintenance[1]
- REPLACE KNIFE[1]
- Replacing consumable parts[1]
- Resuming[1]
- Right cover[1]
- Right pinch roller[1]
- Roll media[1][2]
S
- SCAN INTERVAL[1]
- SENS LEVEL RESET[1]
- Separating knife[1]
- SERIAL NO.[1]
- SERVICE CALL ****[1]
- Setting value[1]
- Setup[1][2]
- SETUP light[1]
- Shafts[1]
- Sheet media[1][2]
- SHEET REMAIN, PRINT MEMO[1]
- SHEET REMAIN, SET AT SETUP[1]
- SHEET REMAIN, SET LENGTH[1]
- SLEEP[1]
- Sleep mode[1]
- Small article storage[1]
- SPEED[1]
- Status LED[1]
- SUBNET MASK[1]
- Sub power switch[1]
- Super cleaning[1]
- SYSTEM INFO.[1]
T
- TEMP. UNIT[1]
- TEMPERATURE IS TOO HIGH **°C[1]
- TEMPERATURE IS TOO LOW **°C[1]
- TEST PRINT[1][2][3][4]
- TEST PRINT NOZZLE MASK[1]
- TEST PRINT POS[1]
- TIME[1]
- TIME FOR MAINTENANCE[1]
- TIME FOR TRAY CLEANING[1]
- TIME FOR WIPER REPLACE[1]
- TO CANCEL, HOLD DOWN PAUSE KEY[1]
- TR2 cleaning liquid pouch replacement[1]
- Tray pad[1]
U
- UP-SPEED[1]
V
- VACUUM POWER[1]
W
- Wiper[1][2]
- Wiper tray[1][2]