Step 1: B. Mounting Pin-type Workpieces on Adapters

Use this section to mount the workpiece on the adapter with a unique ID label, and then secure the workpiece by tightening the adapter cap. You can mount workpieces on any adapters so long as they have unique ID labels. Use the adapter ID to manage the work situations of workpieces.

This step is not necessary when mounting a disc workpiece on the adapter. Proceed to Step 1: A. Mounting Disc Workpieces on Adapters.

Required items
DWX-53DC_AdopterForTable
DWX-53DC_PinDisk
DWX-53DC_PinAdapter_ForTable
DWX-53DC_TorkDriver_ForTable
Adapter Pin-type workpiece Pin-type workpiece adapter Torque screwdriver (0.6 N·m)
IMPORTANT

Do not loosen screws with a torque screwdriver with the sleeve () attached.

Doing so may damage the sleeve. Before loosening screws, remove the sleeve from the torque screwdriver.
WithoutSleeve
IMPORTANT

Before tightening a screw that has a specified tightening torque, be sure to attach a sleeve. Check the marking on the sleeve () and use a sleeve that matches the tightening torque value.

Failure to attach a sleeve will cause a torque in excess of the permitted amount to be applied, which may damage parts and materials.
WithSleeve

1. Mount the pin-type workpiece adapter on the adapter.

Procedure
  1. Make sure that no sleeve is attached onto the torque screwdriver.

    If a sleeve has been attached, remove it.

  2. Use a torque screwdriver with the sleeve removed to loosen the adapter screws (in four locations), turning them approximately four times.
    IMPORTANT

    Use the included spare screws when a screw is lost or worn.

    DWX-53DC_Adopter_Insrall_1
  3. Turn the adapter cap in the direction of the arrows to remove it.
    DWX-53DC_Adapter_Install_2
  4. Mount the pin-type workpiece adapter on the adapter base.
    1. Load the pin-type workpiece adapter () on the adapter base ().
      • Adapter base (): Orient this part so that it looks like a "C."
      • Pin-type workpiece adapter (): Orient this part so the numbers face up.
      DWX-53DC_Adopter_Insrall_4_2
    2. Turn over the loaded adapter, and then align the positions shown in the following figure.

      Attach the pin-type workpiece adapter so that the protrusions on the adapter base () match the positions of the recessed parts on this adapter ().

      DWX-53DC_Adapter_Install_pin_01
    3. Turn over the adapter so that its top faces up, and then check whether the pin-type workpiece adapter has been mounted on the adapter base without any gaps.
      If the parts wobble, check whether the protrusions match the positions of the recessed parts again.
  5. Attach the adapter cap to the adapter base.
    1. Orient the adapter cap removed in step 2 as shown in the following figure.

      Pay attention to the position of the notch.

      DWX-53DC_Adapter_Install_4
    2. Attach the adapter cap to the adapter base, and then turn the cap in the direction of the arrow.
      DWX-53DC_Adapter_Install_pin_4_3
  6. Temporarily tighten the screws (in four locations) with a torque screwdriver so that their seats come into contact with the adapter cap.

    To secure the adapter cap evenly, temporarily tighten the screws before fully tightening them.

    DWX-53DC_Adapter_Install_pin_4_4
  7. Attach the 0.6 N·m, red sleeve onto the torque screwdriver.
    IMPORTANT Be sure to use the 0.6 N·m torque screwdriver sleeve. Failing to do so may lead to loose screws during milling, which will affect the milling quality.
    TorqueDriver_Sleeve_06Nm
  8. Use a torque screwdriver with the sleeve attached to tighten the screws in four locations in the order shown in the following figure.
    IMPORTANT

    Tighten the screws until turning the handle of the torque screwdriver no longer turns the screw bit.

    To maintain milling quality, secure the adapter cap evenly. Be sure to tighten the screws across the diagonals.

    DWX-53DC_Adapter_Install_pin_4_5

2. Mount the workpiece on the pin-type workpiece adapter.

The following figures show the number of workpieces that can be mounted on the adapter according to their sizes. The maximum number of workpieces that can be mounted on the adapter differs depending on the workpiece length ().


DWX-53DC_PinSize_L

Example mounting layouts

 ≤ 20 mm (0.78 in.)
Pin_Adapter_L-20

20 mm (0.79 in.) <  ≤ 50 mm (1.96 in.)
Pin_Adapter_L-20-50

50 mm (1.97 in.) < 
Pin_Adapter_L-50
Procedure
  1. Make sure that no sleeve is attached onto the torque screwdriver.

    If a sleeve has been attached, remove it.

  2. Use a torque screwdriver with the sleeve removed to loosen the screw at the mounting position for the pin-type workpiece.
    MEMO Use the included spare screws when a screw is lost or worn.
    DWX-53DC_PinAdapter_Install_2-1
  3. Mount the pin-type workpiece on the pin-type workpiece adapter.

    Make sure the recessed portion of the pin-type workpiece is oriented downward, align the protrusion of the pin-type workpiece adapter with this recessed portion, and then insert the workpiece all the way in.

    DWX-53DC_PinAdapter_Install_2-2
  4. Attach the 0.6 N·m, red sleeve onto the torque screwdriver.
    IMPORTANT Be sure to use the 0.6 N·m torque screwdriver sleeve. Failing to do so may lead to loose screws during milling, which will affect the milling quality.
    TorqueDriver_Sleeve_06Nm
  5. Use a torque screwdriver with the sleeve attached to tighten the screw.

    Tighten the screws until turning the handle of the torque screwdriver no longer turns the screw bit.

    Check that there is no gap between the pin-type workpiece and the adapter.

    DWX-53DC_PinAdapter_Install_2-3