Step 3: Setting Up the Object

Place the object, and then make it ready for printing.
IMPORTANT

You can set the flat table height while keeping a close eye on it by working with the front cover open.

However, clicking OK in these settings may cause the flat table to start moving. Therefore, when the front cover is open, be careful not to touch any moving parts as you work.

Procedure
  1. On the Utility home screen, click BN2_Icon_Setup Setup.
  2. Register/select the object.
    MEMO In Utility, "media" is used on the window used to register/manage objects.
    • When printing on an object for the first time
      1. Click AddNewIcon.
        BN2_MediaSetup
      2. Enter the name of the new object, and then click OK.

        Previously registered media names cannot be used. Enter a new media name.

        BN2_MediaSetup2
      MEMO

      • We recommend that you set frequently used objects as favorites.

        1. Click BD-8_Utility_Icon_FavoriteOFF next to the name of a registered object to change this icon to BD-8_Utility_Icon_FavoriteON.
        2. Click BD-8_Utility_Icon_Favorite2OFF next to the search box.
          The icon changes to BD-8_Utility_Icon_Favorite2ON, and the list of media set as favorites appears.
          BD-8_Utility_SelectMedia-FavoriteMediaON

      • You can display all registered objects.

        If a rotary axis unit is not attached, the normal objects are displayed. If a rotary axis unit is attached, the objects to be used with this unit are displayed.

        Click BD-8_Utility_Icon_ResisteredMedia-Normal or BD-8_Utility_Icon_ResisteredMedia-Rotary to display all registered objects.

    • For pre-registered objects
      Select the object, and then click OK.
      MEMO You can use the favorites function and the search function to easily find registered objects.
      Steps 3 and 4 are not required. Proceed to step 5.
      IMPORTANT If the height may have changed due to a change in the suction mat or similar, set the height (step 4).
  3. In the Object Type window, select one of the following, and then click OK.
    • Transparent object: Select Smartphone Cases or Others from the Transparent pull-down menu.
    • Opaque object: Select Opaque.
    MEMO
    • Transparent: A hand placed on the other side of the object can be seen through it.
    • Opaque: A hand placed on the other side of the object cannot be seen through it.

    See Object (Media) Registration Items for more information on objects.

  4. Click Change next to Flat Table Height to set the height of the object.
    1. Click AP-640_Panel_Icon_UP or AP-640_Panel_Icon_DOWN on the right side of the window to align the highest point of the object with the forward-back position of the head gap sensor.
      MEMO You can select 0.1 mm (0.004 in.), 1 mm (0.04 in.), 10 mm (0.39 in.), or 50 mm (1.97 in.) as the single-click moving distance.
    2. Click AP-640_Panel_Icon_UP on the left side of the window to have the highest point of the object approach the head gap sensor.
      Move the highest printing position of the object up to a position (a) a few mm away from the head gap sensor without coming into contact with the head gap sensor.
      BD-8_TouchHeadGapSensor-ThinPlate
    3. If the print surface height is not constant or the object is lifted or is warped, see below to set the Flat Table Lowering Amount.
      Setting a Longer Distance between the Object and the Print Heads
    4. Click Automatic Setup.
      The flat table moves and the head gap sensor detects the height of the object.
    5. Click OK.
  5. Click OK.
    If the Printing Area is not set, the maximum printing area (W: 210 mm × L: 148 mm [W: 8.26 in. × L: 5.82 in.]) becomes the Printing Area by default. If you are printing using alignment markers, set to the maximum printing area.
    Setup in progress. is displayed. When setup is completed, you are returned to the home screen, and the registered media name, and the set Flat Table Height, Print Origin, and Printing Area are displayed.