2. A: Determine the positions of the media.

This section describes how to use the suction fan to prevent media skewing. When using transparent media, whose edges cannot be detected, and when "EDGE DETECTION" or "SKEWING CORR" is set to "DISABLE", the suction fan does not activate automatically, so media cannot be loaded with this procedure. In these cases, refer to 2. B: Determine the positions of the media..

Procedure
  1. Determine the left and right positions of the media with the grit patterns used as the reference.
    Note the following points when determining the positions.
    • Hold the media holders from the outside and move them.
    • Ensure that the left edge of the media is positioned so that it is within the range of the grit pattern of the left edge.
    • Ensure that the right edge of the media is positioned so that it is within the range of one of the grit patterns.

    LEC2-640_MediaSet

    CAUTION

    Do not hold places other than those instructed. Do not move the media by holding it directly.

    Otherwise the media may fall off the media holder and cause injury.

  2. Secure the media holders.

    VG2-640_Secure_Media

  3. Use the following procedure to load the media.
    Doing so will prevent media skewing.
    1. Pass the leading edge of the media between the pinch rollers () and the grit rollers ().

      LEC2-640_MediaSet_2

    2. Feed the media until you hear a beep, and then additionally feed approximately 20 cm (7.87 in.) of the media.
      You will hear a beep. Approximately 5 seconds later, you will hear two beeps, and then the suction fan will activate. While this fan is operating, the position of the media will be maintained even if you remove your hands from it.
    3. Hold the media holder flange, turning it in the take-up direction to eliminate the slack in the media.

      VG3_FrangePos

    4. Once the media is taut, additionally take up approximately 10 cm (3.94 in.) of media.

      VG3-Shakouhosei

      MEMO If you take up too much media, you will hear two short beeps and the suction fan will stop. Take up the media, and then redo the procedure from step (1).
  4. Close the rear UV shield.

    LEC2-640_UVShield_Back_Close

  5. (Move to the front of the printer.) Make sure both edges of the media are above the grit rollers.
    Be sure to place the right edge of the media on the right-end grit roller.

    LEC2-640_MediaSet_5

  6. Move the left and right pinch rollers, placing them on both edges of the media.
    Position them approximately 15 mm (0.59 in.) from each edge of the media.

    LEC2-640_MediaSet_6

    IMPORTANT
    • Be sure to use the left and right pinch rollers. The force with which the media is pinched varies between the middle pinch rollers and the left and right pinch rollers. Using the middle pinch rollers to pinch the media edges will lead to unstable media feeding.
    • If you want to readjust the media position, return to the back of the printer, release the media holders, and then redo the procedure from step 1. If you just stand at the front of the printer and hold the media to readjust its position forcibly, the media will be skewed during printing or will come loose, which will affect the printing quality.
    MEMO To smoothly move the pinch rollers, push down close to the rail.

    LEC2-300_pinchroller_move

  7. Move the middle pinch rollers () over all the remaining grit rollers covered by the media ().
    There are grit patterns () wherever there are grit rollers.

    LEC2-640_MediaSet_7

    IMPORTANT
    • Place the middle pinch rollers over all the grit patterns within the media width. If you have forgotten to place the middle pinch rollers, the media will be skewed during printing or will come loose, which will have an effect on the printing quality.
    • There may be extra middle pinch rollers depending on the width of the media being used. Remove the remaining middle pinch rollers.

      LEC2-640_MediaSet_9

  8. Lower the loading lever (front).
    At this time, the message "PRESS ENTER KEY TO SET UP" is displayed on the screen, but do not press [ENTER] yet, and proceed to the next step.
    IMPORTANT If you want to readjust the media position, return to the back of the printer, release the media holders, and then redo the procedure from step 1. If you just stand at the front of the printer and hold the media to readjust its position forcibly, the media will be skewed during printing or will come loose, which will affect the printing quality.