Touch Panel


PN_touch_panel

Part Name Details Notation in this manual
TP_bt_START-X
START X key Returns the printer unit to the front of the table. Press and hold until the printer begins moving. [TS : START X]
TP_bt_STOP
STOP key Stops the printer unit when moving to a specified location. [TS : STOP]
TP_bt_END-X
END X key Moves the printer unit to the back of the table. Press and hold until the printer begins moving. [TS : END X]
TP_bt_FRONT
FRONT key Moves the printer unit to the front. The printer moves while the key is pressed and stops moving when the key is released. [TS : FRONT]
TP_bt_BACK
BACK key Moves the printer unit to the back. The printer moves while the key is pressed and stops moving when the key is released. [TS : BACK]
TP_vw_Pos-X
X coordinates

Displays the current position in the feed direction (toward the front and back of the table) using the front of the table as the origin (zero).

The lamp lights in green during normal operation and in red when an error occurs.

[TS : X]
TP_bt_Pos-X
Move to X coordinates Press dentak_icon, and then enter the distance to move from the front position. Press and hold X_icon to move the printer unit the set value in the feed direction. [TS : X -▶]
TP_vw_Pos-Z
Z coordinates

Displays the current position in the vertical direction using the lowest point of the printer unit as the origin (zero).

The lamp lights in green during normal operation and in red when an error occurs.

[TS : Z]
TP_bt_Pos-Z
Move to Z coordinates Press dentak_icon, and then enter the distance to move from the lowest point. Press and hold Z_icon to move the printer unit the set value up. [TS : Z -▶]
TP_bt_START-Z
START Z key Moves the printer unit to the highest point. Press and hold until the printer begins moving. [TS : START Z]
TP_bt_RESTART
RESTART key Restarts the transporter and sets the machine origin again. [TS : RESTART]
TP_bt_AUTO-Z
AUTO Z key Detects the print surface height of the object to be printed on. The printer will descend while the key is pressed and automatically stop when the height is detected. If the key is released before the height is detected, the printing height will be set to that height. [TS : AUTO Z]
TP_bt_UP
UP key Lifts the printer unit up. The printer moves while the key is pressed and stops moving when the key is released. [TS : UP]
TP_bt_DOWN
DOWN key Lowers the printer unit. The printer moves while the key is pressed and stops moving when the key is released. [TS : DOWN]
TP_bt_VACUUM
BLOWER_Icon_Icon
VACUUM/BLOW key Suctions the object to be printed on against the table when set to VACUUM. Applies air against the object to be printed on when set to BLOW. Normally set to VACUUM. Set to BLOW if the object to be printed on is heavy and not easily moved. [TS : VACUUM/BLOW]
TP_bt_PUMP
PUMP1 key Switches the vacuum or blower pump on or off. Pump 1 controls the vacuum or blower from the center to the front of the table. [TS : PUMP1]
Pump
PUMP 2 key Switches the vacuum or blower pump on or off. Pump 2 controls the vacuum or blower from the center to the back of the table. [TS : PUMP2]
IONIZER_Icon
IONIZER key

Switches the ionizer on or off.

The ionizer neutralizes the static electricity within the machine and the object. This can reduce issues caused by static electricity such as ink landing position misalignment and adhesion of dust on the object.

[TS : IONIZER]
TP_bt_ALARM
ALARM key Displays warning and error information. [TS : ALARM]
TP_bt_RESET
RESET key Press and hold this key to cancel the warning beep and clear the error. [TS : RESET]
TP_bt_PUMP_%
PUMP % key Adjusts the vacuum or blower pump strength. [TS : PUMP %]
TP_bt_LIGHT
LIGHT key Switches the internal lighting on or off. [TS : LIGHT]
TP_bt_SYSTEM
SYSTEM key Used by service technicians. Do not use this key. [TS : SYSTEM]
TP_bt_SETUP
SETUP key Used by service technicians. Do not use this key. [TS : SETUP]
TP_Arrow
ARROW key Displays the language selection menu. Also, when an error occurs, you can press the ALARM key followed by this key to return to the original screen. [TS : ARROW]