Installation and Initial Settings

Ethernet Connection

Installing the Software
    Important

    If CutStudio is already installed on the computer to connect to this machine, uninstall this software.

    Installing the Software with the IP Address Set Automatically

  1. Double-click the downloaded [Roland_DG_GS2-24_Full_Package_Web_Installer.exe] file.
    When the [User Account Control] window appears, click [Yes] (or [Allow]). The setup menu screen appears automatically.
  2. Select the software to install.
    Click the check boxes under "Software List" to select them.
    MEMO

    [GS2-24_Full_Package_Web_Installer.exe] will install the selected software in order.

    select
    Click [Start] and follow the on-screen instructions to proceed with the installation.

    Note the following points during an installation with an Ethernet connection.
    • When the following window appears, select [Install], [Roland DG GS2-24] for the Model, and [IP_(AUTO)] for the Port, and then click [Start].
      lan_connect-1

    • If the machine cannot be detected, check the following points, and then click [Refresh].
      • The machine is on.
      • The machine is connected to the same LAN as the computer by an Ethernet cable.
      • The computer is connected to the same LAN as the machine.
      setup_ip_ng.png
      If the machine cannot be detected even after clicking [Refresh], proceed to Setting the IP Address Manually.

      After completing the network settings, restart the installation. Do not close the window.

  3. When the installation is complete, from [Control Panel], click [View devices and printers]. When the machine appears under "Printers," this procedure is complete.

Setting the IP Address Manually
If you cannot set the IP address automatically, use the following procedure. If the settings were configured automatically, this procedure is not necessary.

    1. Determining the Network Addresses

    The settings listed here are only an example. The procedure and settings given in this manual do not match every environment. In an environment where the computer being used is connected to multiple network devices and the Internet, inappropriate settings will have a large effect on the entire network. For detailed information about the settings, consult your network administrator.

    Determine the IP addresses, subnet mask, and default gateway to connect the computer and this machine to a network.

  1. Determine the IP addresses.
    • Computer: 192.168.0.XXX
    • Device: 192.168.0.YYY

      • "XXX" and "YYY" represent numbers from 1 to 254. Ensure that they are different from the numbers of other network equipment.

  2. Determine the subnet mask.
    • Computer: 255.255.255.0
    • Device: 255.255.255.0

      • Use the same number for the computer and this machine.

  3. Determine the default gateway.
    • Computer: 192.168.0.AAA
    • Device: 192.168.0.AAA

      • "AAA" represents numbers from 1 to 254. It may not be necessary to set this number, so check with your network administrator.

    2. Setting the Computer's Network
    This step is not necessary when connecting to an existing network environment.

  1. Display the "Ethernet Properties" screen.
    Windows 11:
    1. On the [Start] menu, click [Settings].
    2. Click [Network ＆ Internet], and then click [Dial-up].
    3. Click [Network and Sharing Center].
    4. Click [Ethernet] or [Wi-Fi].
    5. Click [Properties].
    Windows 10:
    1. On the [Start] menu, click [Settings], and then click [Network ＆ Internet].
    2. Click [Network and Sharing Center].
    3. Click [Ethernet] or [Wi-Fi].
    4. Click [Properties].
    Windows 8.1:
    1. On the [Start] menu, click [PC settings], and then click [Control Panel].
    2. Click [Network ＆ Internet], and then click [Network and Sharing Center].
    3. Click [Ethernet] or [Wi-Fi].
    4. Click [Properties].
  2. Select [Internet Protocol Version 4 (TCP/IPv4)], and then click [Properties].
    If the [Internet Protocol Version 4 (TCP/IPv4)] check box was clear, click the check box to select it.
    property_ethernet
  3. Select [Use the following IP address], and then enter the computer network addresses determined under [1. Determining the Network Addresses].
    property_ipaddress
  4. Click [OK].
  5. Close all the windows opened for the network settings.

    3. Setting the Machine's Network

  1. If the machine is off, press the power button to start the machine.
    power1
  2. Press [MENU] twice to display the screen shown below.
    lcd_cut
  3. Press [▼] once to display the screen shown below.
    lcd_sysinfo
  4. Press [▶] once to display the screen shown below.
    lcd_infomodel
  5. Press [▼] three times to display the screen shown below.
    lcd_infointer
  6. Press [▶] twice to display the screen shown below.
    lcd_dhcp
  7. Press [▶], then [▼] to set DHCP to OFF.
    lcd_dhcp2
  8. Press [ENTER].
  9. Press [▼] once to display the screen shown below.
    lcd_ip
  10. Press [▶] twice.
  11. Set the IP address.
    1. Press [▲] or [▼] to enter the IP address of the machine determined under [1. Determining the Network Addresses].
      Press [◀] or [▶] to move the cursor.
    2. Press [ENTER].
  12. Press [◀], then [▼] to display the screen shown below.
    lcd_subnetip
  13. Press [▶] twice.
  14. Set the subnet mask.
    1. Press [▲] or [▼] to enter the subnet mask of the machine determined under [1. Determining the Network Addresses].
      Press [◀] or [▶] to move the cursor.
    2. Press [ENTER].
  15. Press [◀], then [▼] to display the screen shown below.
    lcd_gateway
  16. Press [▶] twice.
  17. Set the gateway address.
    1. Press [▲] or [▼] to enter the gateway address of the machine determined under [1. Determining the Network Addresses].
      Press [◀] or [▶] to move the cursor.
    2. Press [ENTER].
  18. Press [MENU] to return to the original screen.

    4. Restarting Installation

  1. Note the following points and restart the software installation.
    Follow the on-screen instructions to proceed with the installation.
    • Click [IP Setting] and enter the IP address of the machine determined under [1. Determining the Network Addresses].
      setup_ip_ng1.png
      After entering the IP address, click [OK].
      ipadd.png
  2. When the installation is complete, from [Control Panel], click [View devices and printers]. When the machine appears under "Printers," this procedure is complete.