Menu List

Tap Menu_Panel to display the following list of operations to perform from the screen.

MEMO Media Settings only appears when media has been set up.
Level 1 Level 2 Level 3 Level 4 Details
Media Settings List of Media Settings Lists the settings of the media that has been set up. Tap a setting to move to a screen for changing this setting.
Printing settings Print Head Height Checks/changes the print head height.
Batch Automatic Correction Adjustments are performed in the following order: Multi Sensor Adjustment then Media Gap Adjustment.
Feed Correction Adjusts the media feed amount during printing. With Detailed Correction (Manual), a test pattern is printed, and then the correction value is entered manually after the printed correction value is checked visually.
Media Gap Adjustment Simple Correction (Auto) Corrects the ink landing position. A test pattern is printed and then read with a sensor to automatically set the correction value.
Detailed Correction (Manual) Corrects the ink landing position. With Detailed Correction (Manual), a test pattern is printed, and then the correction value is entered manually after the printed correction value is checked visually.
Heater Temperature Print Heater Switches the print heater on/off and changes the set temperature.
Oven Changes the temperature setting of the oven.
Advanced Oven Settings Changes the individual oven set temperatures. Advanced Oven Settings under Preferences appears.
Other Media Settings Multi Sensor Adjustment Optimizes the status of the multi sensor used with the automatic correction function.
Media Suction Force Adjusts the media suction force of the platen.
Media Sticking Prevention When set to Enable, the media is peeled off before printing.
Batch Media Settings The minimum settings required for media setup can be configured by following the on-screen instructions on the operation panel.
Media Management Displays a list of registered media (up to 50 entries). The following operations are available.
  • Checking setting details in a list
  • Changing media names
  • Copying media settings
  • Deleting media settings
Cleaning Printing Test

Before printing, use Nozzle Drop-out Test to check whether ink is discharged from the print heads correctly. If dot drop-out is present, perform cleaning appropriate for the severity of the drop-out. If faulty ink discharge cannot be improved, the problematic nozzle can be identified with Nozzle Mask Test, making it possible to stop using this nozzle.

Normal Cleaning

If dot drop-out or dot displacement occurs, select the nozzle and then perform cleaning of the print heads. If the problem cannot be fixed, perform more powerful cleaning.

Powerful Cleaning also has the effect of improving uneven colors.

If the media has already been set up, the After cleaning, perform a printing test. menu appears. When this is turned on, a printing test is performed after cleaning.

Medium Cleaning
Powerful Cleaning
Manual Cleaning Use cleaning liquid and a cleaning stick to clean the area around the print heads.
Maintenance Wiper Replacement Replace the wipers.
Separating Knife Replacement Replaces the separating knife used in media separation.
Cap Replacement Replaces the print head caps, which are used to protect the print heads from drying out and from dust.
Wiper Cleaner Replacement Replaces the wiper cleaner used to wipe away dirt from the wiper.
Flushing sponge

To replace the flushing sponges used to absorb the flushed ink, tap Execute next to Replacing the Flushing Sponges.

To drip cleaning liquid on the flushing sponge used for CMYK ink, tap Execute next to Cleaning Liquid Replenishment.

Ink Renewal Perform this operation when ink discharge issues or uneven colors are not resolved even after Normal Cleaning, Medium Cleaning, Powerful Cleaning, and Manual Cleaning. However, this operation consumes a large amount of ink and may damage the print heads, so do not perform it more than necessary.
Light Choke Cleaning Perform this operation when ink discharge issues or uneven colors are not resolved even after Ink Renewal.
Drain bottle Use this menu to discard discharged fluid at any desired time, regardless of any notifications or errors.
Preferences Embossing Light Select On, Off, or AUTO for the embossing light (the light that is near the take-up unit and is used to check the foaming status of the media after heating). Select AUTO to automatically turn the light on/off according to the status of the printer.
Take-up Take-up Mode Select On, Off, or AUTO for the operation of the take-up unit.
Take-up Method Select either Tension Winding or Slack Winding for the media take-up method. These options result in either constant tension or a little slack during media take-up.
Remaining Media Management

Sets the amount of remaining media that has been set up and displays this amount. This amount can also be printed on the media.

Skewing Correction Support at Setup Provides support, preventing skewed installation of the media by making a sound and operating an automatic suction fan during setup.
Standby Heater Temperature Sets the heater temperature and oven temperature when media has not been set up.
Advanced Oven Settings Separately adjusts the temperature setting of the oven's built-in heater. The adjustment range is ±30°C (±54°F) in relation to the internal temperature setting.
Heating regulation due to the internal temperature of the oven At the start of heating, the temperature of the heater in the oven will be fine-tuned according to the temperature of the media. The temperature of the media at the start of heating varies according to the internal temperature of the oven and the thermal conductivity of the media.
Ink Empty Mode This menu lets you determine the operation that takes place when an ink cartridge becomes empty during printing. The print quality will be affected by the selected operation.
Notifications On/Off When this is set to on, notifications are displayed at the appropriate times.
  • Media Clamp Placement Notification
Sleep Time Sets the time until sleep mode (the state in which the power-saving features operate) activates.
Reset to Factory Defaults Returns all settings other than Language and Units to their factory default values.
System information Machine Information Displays the Model, Serial Number, Ink Type, Firmware Version, and MAC Address.
Network Sets the Obtain IP Address Automatically, IP Address, Subnet Mask, and Default Gateway to connect the machine to a computer.
Units Sets the Length unit and Temperature unit.
Language Sets the language.
Date/Time Sets the current year, month, day, hour, minute, and second.
Screen Appearance Selects the color scheme of the operation panel's screen.
Screen Brightness Sets the brightness of the operation panel's screen.
Screen Operation Sound Turns the operation sound of the operation panel on/off.
License Displays the license information of the operation panel.