1. Determine the positions of the media.

When loading sheet media in the machine, use the right edge of the media as a reference. This is because the range of movement of the right pinch roller is fixed.

Place the media in a position where the following conditions are met and where media waste will be minimized.
  • Position of right edge of media

    Within the right pinch roller movable range and where about 10 mm (0.39 in.) between the right roller edge of the right pinch roller and the right edge of the media can be secured.

  • Position of left edge of media

    Where about 10 mm (0.39 in.) between the left edge of the roller and the left edge of the media can be secured when placing the left pinch roller within the range of the grit pattern.


    Setup_CutMedia

MEMO

Use the following link to view a reference video for this procedure. We recommend that you view this video to understand the overall flow of work.

https://youtu.be/y3pYUMM4tCs
y3pYUMM4tCs

The BN2-20/20A is shown in this video, but the work and operation procedures are the same for this machine.

Procedure
  1. Open the front cover.
    FrontCoverOpen
  2. Move the right pinch roller () and the right media clamp () to the right end.

    Press the part indicated by the arrow on the right pinch roller to move the roller and the right media clamp together.

    MoveClampPinch_R
  3. Move the left pinch roller () and the left media clamp () to a position farther left than the media width.

    Press the part indicated by the arrow on the left pinch roller to move the roller and the left media clamp together.

    MoveClampPinch
  4. Use the following procedure to load the media.
    1. Pass the media () under the right media clamp ().
      MEMO

      If the left edge of the media hits the left media clamp, pass the media under the left media clamp.

      MEMO

      Lifting the tip of the media clamp to pass the media through may cause the blade to come into contact with the media. Be careful not to allow contact with the blade.

      CutMedia1
    2. Pass the media () between the right grit roller () and the pinch roller () and feed the media to the back.

      Feed the media and line up the edge of the media with the edge of the apron ().

      MEMO

      If the left edge of the media is left of the left pinch roller, pass the media between the left grit roller and left pinch roller as well.

      CutMedia2
  5. Straighten the media.
    CutMedia3
  6. Press lightly on the media, and place the left media clamp and left pinch roller on the media.
    1. Position the left pinch roller within the range of the grit pattern .

      Ensure that margin A from the left edge of the media to the left edge of the left pinch roller is at least 10 mm (0.4 in.).

      PinchPos
      MEMO

      If at least 10 mm (0.4 in.) cannot be ensured for margin A from the left edge of the media to the left edge of the left pinch roller, move the right pinch roller and the media to the left to provide the margin.

      The range of motion of the right pinch roller is fixed. Place the right pinch roller within the movable range in a position that ensures margin A from the right edge of the media to the right edge of the right pinch roller is about 10 mm (0.39 in.).
      MediaSet5
    2. Adjust the right media clamp position as necessary.
      Click BN2_Panel_Icon_MENU > Preferences - Media Clamp Position - Execute to move the print-head carriage to the left side, allowing you to adjust the right media clamp position.

      Line up the edge of the media with the centers of the holes of the right media clamp.

      ClampR_Set
  7. Lower the loading lever.
    LeverDown2
  8. Line up the edges of the media with the centers of the holes of the left media clamp.
    MediaSet6
  9. Feed the media in the feed direction, checking that the media stays aligned with the pinch rollers.
    1. On the home screen, click UtilityMove.

      The Move window appears.

      UtilityMove3
    2. Select an option under Moving Distance / Click, and then click UtilityMoveDOWN.

      Feed approximately 2/3 of the length of the media and check that the media stays aligned.

      If the media comes off or is not straight, redo the procedure from step 4.

    3. Click UtilityMoveUP to return to the position before feeding.

      If the media comes off or is not straight, redo the procedure from step 4.

  10. Click Cancel.
    The Move window closes.
  11. Close the front cover.