Printer Unit

Front

No.	Name	Function overview
	Ink slots	Store the ink cartridges. Insert ink cartridges in which ink pouches have been loaded.
	Front cover	Prevents contact with the print heads and other such fast-moving parts when the machine is operating. This cover also blocks ultraviolet light from the UV lamp and prevents dust from entering the machine. Keep this cover closed when not loading media or performing maintenance.
	Operation panel	Used to perform all machine operations including printing, setup, and maintenance. Operation Panel
	Left cover	Provides access to the interior of the left side of the machine. Open this cover when performing maintenance such as cleaning around the print heads.
	Right cover	Provides access to the interior of the right side of the machine. Open this cover when performing maintenance such as cleaning and part replacement.
	Loading lever (front)	Secures the media in place and releases it. Use this lever when working at the front of the machine. Lowering the lever secures the media in place.
	Take-up Unit	Takes up the media after printing. This prevents the printed media from touching the floor.

Rear

No.	Name	Function overview
	Loading lever (rear)	Secures the media in place and releases it. Use this lever when working at the back of the machine. Lowering the lever secures the media in place.
	Rear UV shield	Blocks the light from the UV lamp during printing. Open this shield when you load the media and close it when you are finished loading the media. Printing is not possible with the UV shield open.
	Media stays	Temporarily hold the roll media in place. Temporarily place the roll media on these stays when loading this media on the media holders.
	Shafts	Used to adjust the positions of the media stays and media holders. The media stays and media holders are moved to the left or right along this shaft to match the width of the media.
	Media holders	Hold the roll media. Fit the paper tube of the media onto the end caps of the media holders.
	Drain bottle	Accumulates the discharged cleaning liquid and ink. When discharged fluid is nearly overflowing from the bottle, an error is displayed and printing is not possible.
	Main power switch	Switches the main power of the machine on/off.
	Power-cord connector	Used to connect the power cable from which power is supplied to the machine.

Side

No.	Name	Function overview
	Ethernet connector	Use this to connect an Ethernet cable.
	Cleaning liquid slot	Stores a cleaning cartridge containing a cleaning liquid pouch.

Front Cover Interior/Print Head Area

No.	Name	Function overview
	UV-LED device	Shines the UV light on the print surface to cure the ink.
	UV mist filters	Absorb the ink mist that flows into the UV-LED device.
	Print-head carriage	Transports the built-in print heads and UV-LED device.
	Cutting carriage	The blade and the separating knife are inside here. This part transports the blade and separating knife to the left and right.
	Blade holder	Holds the blade used during cutting.
	Separating knife	The knife used to separate the media.
	Wiper	Cleans the print heads, removing dirt and excess ink that have adhered to these heads.
	Wiper cleaner	Removes ink and dirt that have adhered to the wiper.
	Flushing sponge	Absorbs ink flushed from the print heads.
	Print head caps	Prevent the print heads from drying out by sealing the print heads to protect the ink emission surface when the print heads are at the right side of the machine, such as when waiting for printing.
	Media clamp	Each clamp holds down the left or right edge of the media, keeping the media from coming loose and preventing fuzz on the cut edge of the media from touching the print heads.
	Grit roller	Transports the media.
	Grit pattern	This indicates the location of a grit roller. When loading media, be sure to place the pinch rollers within the ranges indicated by these patterns.
	Pinch roller (left pinch roller, right pinch roller, and middle pinch roller)	Each pinch roller is lowered/raised according to the operation of the loading levers. Lowering a loading lever lowers the pinch rollers, clamping the media. The pinch rollers are called the left pinch roller, the right pinch roller, and the middle pinch roller according to their positions.
	Blade protector	This is the path that the blade takes during cutting. It protects the tip of the blade.
	Platen	This is the path over which the media passes. A suction fan that keeps the media from coming loose is built in.
	Apron	This is the path over which the media passes. The apron has a built-in heater that heats the media and prevents it from coming loose.

If a Cover Opens during Operation

If the front cover, left cover, right cover, or rear UV shield (hereinafter these items are all referred to as the "cover") opens during an output operation, the machine makes an emergency stop. When an emergency stop occurs, a message prompting you to close the cover appears on the screen. Close the covers as directed in the instructions shown on the screen.

When the cover is closed, you will be able to continue the operation.

If you cannot continue the operation even after you close the cover, a nonrecoverable error may have occurred.