跳转到主要内容
使用者手冊
基本使用方法
加工方法
優化品質與效率
保養
故障因應方法
索引
索引
搜索
主页
故障因應方法
訊息因應方法
VPanel的錯誤訊息
****-****An unknown error occurred.
基本使用方法
加工方法
優化品質與效率
保養
故障因應方法
機器問題
加工品質問題
安裝問題
訊息因應方法
VPanel的錯誤訊息
1000-****The % limit switch was not found.
1006-02**The % axis position has been shifted.
1017-0000The front cover was opened.
101C-0000The milling bur sensor was not found.
101D-00**The % milling bur cannot be released.
101D-01**%號刀具沒有被釋放。其根部可能已斷裂。
101E-****The % milling bur might be broken.
101F-****The % milling bur chucking has slipped out.
1020-****The % milling bur is too long.
1021-****The % milling bur is too short.
1022-****The % milling bur was not found.
1023-0000～1028-0000Milling data error.
1029-0000The spindle experienced an overload.
102A-0000The spindle experienced an overload.
102B-0000The spindle motor temperature is too high.
102D-0000The spindle can not be turned.
102D-0001The spindle abnormally stopped during milling.
102E-0000A moving part has collided with other components.
1030-0001必須更換集塵過濾器。
1038-0000銑削數據錯誤。未選擇刀具。
103B-0000The automatic correction is not yet finished.
103D-0000Milling data error. The milling bur cannot reach the milling position.
105F-****吹走切削粉塵的壓縮空氣壓力超出範圍。
****-****An unknown error occurred.
其他錯誤訊息
****-****
An unknown error occurred.
重新啟動機器。
錯誤再次發生時
請聯繫本公司授權經銷商或本公司客服中心。
基本使用方法
加工方法
優化品質與效率
保養
故障因應方法
機器問題
加工品質問題
安裝問題
訊息因應方法
VPanel的錯誤訊息
1000-****The % limit switch was not found.
1006-02**The % axis position has been shifted.
1017-0000The front cover was opened.
101C-0000The milling bur sensor was not found.
101D-00**The % milling bur cannot be released.
101D-01**%號刀具沒有被釋放。其根部可能已斷裂。
101E-****The % milling bur might be broken.
101F-****The % milling bur chucking has slipped out.
1020-****The % milling bur is too long.
1021-****The % milling bur is too short.
1022-****The % milling bur was not found.
1023-0000～1028-0000Milling data error.
1029-0000The spindle experienced an overload.
102A-0000The spindle experienced an overload.
102B-0000The spindle motor temperature is too high.
102D-0000The spindle can not be turned.
102D-0001The spindle abnormally stopped during milling.
102E-0000A moving part has collided with other components.
1030-0001必須更換集塵過濾器。
1038-0000銑削數據錯誤。未選擇刀具。
103B-0000The automatic correction is not yet finished.
103D-0000Milling data error. The milling bur cannot reach the milling position.
105F-****吹走切削粉塵的壓縮空氣壓力超出範圍。
****-****An unknown error occurred.
其他錯誤訊息
Feedback
Was this information helpful?
1
2
3
4
5
NO
YES
Any additional feedback to help us improve.
Feedback
Thank you
