Part Names and Functions

Front

	Milling area cover	Covers the milling area. Workpieces are milled in the milling area. It is also a location where machine maintenance, such as cleaning and collet replacement, is performed. ^*1
	Dust-proof cover	Prevents the work area from getting dirty from milling waste ejected from the milling area. Be sure to attach the dust-proof cover before milling with this machine.
	Adapter area cover	Covers the adapter area. Adapters are installed in and removed from the disc changer in the adapter area. ^*2
	Tool area cover	Covers the tool area. Milling burs used in milling and detection pins are loaded in the ATC magazine in the tool area.^*1
	Built-in panel	The LED lights on the built-in panel display the status of the machine. When the machine is connected to a dust collector with built-in linking function, pressing the touch sensor with a cover open turns the dust collector on.
	Tablet base	Use this part when operating the machine with a tablet. When using a tablet, use the included tablet holders and cushions.
	Bottom storage	Use this area to store items such as replacement tools and maintenance parts.

^*1 For safety, the machine stops if this cover is opened during operation.

^*2 For safety, the machine stops if this cover is opened during adapter replacement.

CAUTION

Be careful with the cover.

The edges of the cover are sharp. To avoid injury, exercise caution.

Milling Area

	Ionizer	The ionizer works to eliminate static electricity from milling waste when cutting PMMA. This makes it easier for the milling waste to move away from the material during milling, which has the effect of maintaining the milling quality. ^*3
	Status light	This light is linked with the status light at the top of the machine and indicates the status of the machine with its color and depending on whether it is lit or flashing.
	Camera	The camera allows the milling status of the machine to be checked from VPanel. When the camera settings are configured, recording starts at the same time as milling. Images are automatically saved only when an error occurs. The images are useful in checking the milling status and in identifying the causes of errors.
	Rotary axis unit	Rotates the adapter to which the material to mill is attached, allowing the milling bur to cut the material according to the CAM data sent to the machine.
	Clamp	Removes the specified adapter from the adapter magazine and holds this adapter until milling is complete.

^*3 To obtain the optimal ionizer effect, ground this machine.

Adapter Area

	Adapter stocker number	Displays the adapter stocker number. Each number has a disc stocker light to indicate the status of the machine and of the adapter installed in the stocker.
	Adapter magazine	Load adapters, in which the pre-milling workpieces and automatic correction jigs have been set, here. Up to six adapters can be loaded in the machine. When milling data is sent from the computer, the clamp automatically grips the adapter loaded in the magazine, and milling starts.
	Adapter stocker	Install adapters, in which workpieces have been loaded, and automatic correction jigs here.

Tool Area

	Milling bur stockers	Load the milling burs and detection pins to use in milling and correction here.
	Milling bur sensor	Judges whether the amount of extension of the milling bur gripped by the spindle unit is appropriate. To maintain good sensor accuracy, clean this part periodically.
	ATC magazine	Transports milling burs and detection pins used in milling to the spindle unit. When milling data is sent from the PC, the spindle unit grips the milling bur in the stocker with the specified number, and milling starts.
	Maintenance cover	Covers the aperture used for machine maintenance such as spindle unit and spindle belt replacement.
	Spindle belt^*4	Conveys the rotation of the spindle motor to the spindle unit. The spindle belt is a part that wears out. To maintain highly accurate milling quality, replace it at the appropriate time.
	Spindle unit^*4	Conveys the rotation of the spindle belt to the milling bur. The spindle unit is a part that wears out. To maintain highly accurate milling quality, replace it at the appropriate time.
	Air nozzle^*4	Discharges compressed air during milling to blow milling waste away from the workpiece.
	Collet^*4	This part is attached to the tip of the spindle unit and grips the milling bur or detection pin used in milling and correction. The collet is a part that wears out. To maintain highly accurate milling quality, replace it at the appropriate time.
	Dummy pin^*4	This is a milling bur dummy. It is attached to the spindle upon shipment. A malfunction may occur if the collet does not grasp anything, so have it grasp the dummy pin when it is not grasping a milling bur.

^*4 Inside the maintenance cover

Side/Rear

	Status light	This light is linked with the status light in the milling area and indicates the status of the machine with its color and depending on whether it is lit or flashing.
	Compressed air intake	This is the intake for the compressed air adjusted by the regulator. The compressed air is used, for example, to blow away the waste generated when milling workpieces.
	Expansion port	Use this port to connect a dust collector with built-in linking function. Connect a linking cable to the expansion port.
	USB connector	Use this connector to connect the USB cable between this machine and the computer.
	Tablet cable insertion port	Pass the cables used to connect this machine and the tablet through this port. Pull the tablet base toward you, and then pull the cables from the aperture on the right side.
	Power switch	Turns the machine's power on and off.
	Power cord connector	Connect the supplied power cord to this connector.
	Dust collection hose attachment port	Attach the dust collection hose to this port. Attach the dust collection hose included with the dust collector you are using.

Statuses Indicated by Status Light Color

Status Lights at the Top of the Machine and in the Milling Area

To ensure that operators can determine the status of the machine whether they are right next to it or far away, one status light is provided in the milling area () and another on the top of the machine (). These two synchronized lights display the status of the machine.

Blue	Lit	The machine is in standby. To reduce power consumption, if no operation is performed for 30 seconds while the machine is in standby, the machine will change to the sleep status, and the status lights will turn off.
Blue	Flashing	The machine is undergoing the initial operation after it turns on. Alternatively, maintenance such as automatic correction and spindle run-in is in progress.
White	Lit	Milling is being performed or has been paused or the milling area cover or tool area cover is open.
White	Flashing	The dust collector is in standby.
Yellow	Lit	An error has occurred during milling, and the machine has been paused. Check the error details shown on VPanel. Press the touch sensor on the built-in panel to resume milling.
Yellow	Flashing	An error occurred during adapter replacement, and the machine has restarted. Follow the instructions displayed in VPanel to remove the adapter.
Red	When lit or flashing in red, an error has occurred and milling has been stopped. Milling cannot be resumed.
	Lit	Hold down the touch sensor on the built-in panel to cancel milling and return the machine to the ready status.
	Flashing	Turn the machine off, and then restart it.
Off	The status lights turn off when the machine is in the sleep state or the power is turned off.

Disc Stocker Lights

White	Lit	A pre-milling adapter has been installed.
	Flashing	During disc changer operation, all status lights flash. Do not open the covers until the lights stop flashing and remain on.
Blue	An adapter for which milling is not scheduled has been installed. Remove adapters for which milling is complete from the adapter stocker.
Yellow	Adapters attached to the stocker have duplicate IDs or an error occurred when recognizing adapters. Check the adapter IDs.
Off	The lights turn off in the following situations. No adapters have been installed in the stocker. The machine is off.