跳转到主要内容
使用者手冊
基本使用方法
加工方法
優化品質與效率
保養
故障因應方法
索引
索引
搜索
主页
故障因應方法
訊息因應方法
VPanel的錯誤訊息
103A-000*DANGER!! The coolant is leaking!!
基本使用方法
加工方法
優化品質與效率
保養
故障因應方法
機器問題
加工品質問題
安裝問題
訊息因應方法
VPanel的錯誤訊息
1000-****The % limit switch was not found.
1006-02**The % axis position has been shifted.
101C-0000The milling bur sensor was not found.
101D-00**The % milling bur cannot be released.
101D-01**The % milling bur cannot be released. It might be broken from the root.
101E-****The % milling bur might be broken.
101F-****The % milling bur chucking has slipped out.
1020-****The % milling bur is too long.
1021-****The % milling bur is too short.
1022-****The % milling bur was not found.
1023-0000~1028-0000Milling data error.
1029-0000The spindle experienced an overload.
102A-0000The spindle experienced an overload.
102B-0000The spindle motor temperature is too high.
1034-0000The coolant tank is not installed.
1038-0000Milling data error. No milling bur is selected.
103A-000*DANGER!! The coolant is leaking!!
103B-0000The automatic correction is not yet finished.
103D-0000Milling data error. The milling bur cannot reach the milling position.
105E-0000The pressure of the compressed air is too high or low.
1062-0000An error occurred during the automatic correction.
1063-0000The milling cannot be started because the coolant has exceeded its expiration date.
****-****An unknown error occurred.
103A-000*
DANGER!! The coolant is leaking!!
狀況/錯誤原因
本體內部可能漏水。
步驟
關閉電源。
拔下電源插頭。
請聯繫本公司授權經銷商或本公司客服中心。
關聯資訊
https://www.dgshape.com/
基本使用方法
加工方法
優化品質與效率
保養
故障因應方法
機器問題
加工品質問題
安裝問題
訊息因應方法
VPanel的錯誤訊息
1000-****The % limit switch was not found.
1006-02**The % axis position has been shifted.
101C-0000The milling bur sensor was not found.
101D-00**The % milling bur cannot be released.
101D-01**The % milling bur cannot be released. It might be broken from the root.
101E-****The % milling bur might be broken.
101F-****The % milling bur chucking has slipped out.
1020-****The % milling bur is too long.
1021-****The % milling bur is too short.
1022-****The % milling bur was not found.
1023-0000~1028-0000Milling data error.
1029-0000The spindle experienced an overload.
102A-0000The spindle experienced an overload.
102B-0000The spindle motor temperature is too high.
1034-0000The coolant tank is not installed.
1038-0000Milling data error. No milling bur is selected.
103A-000*DANGER!! The coolant is leaking!!
103B-0000The automatic correction is not yet finished.
103D-0000Milling data error. The milling bur cannot reach the milling position.
105E-0000The pressure of the compressed air is too high or low.
1062-0000An error occurred during the automatic correction.
1063-0000The milling cannot be started because the coolant has exceeded its expiration date.
****-****An unknown error occurred.
Feedback
Was this information helpful?
1
2
3
4
5
NO
YES
Any additional feedback to help us improve.
Feedback
Thank you