跳转到主要内容
用户手册
基本使用方法
加工方法
优化质量和效率
保养
故障排除方法
索引
索引
搜索
主页
故障排除方法
对提示信息的处置方法
VPanel的错误信息
****-****An unknown error occurred.
基本使用方法
加工方法
优化质量和效率
保养
故障排除方法
机器问题
加工品质问题
安装问题
对提示信息的处置方法
VPanel的错误信息
1000-****The % limit switch was not found.
1006-02**The % axis position has been shifted.
101C-0000The milling bur sensor was not found.
101D-00**The % milling bur cannot be released.
101D-01**The % milling bur cannot be released. It might be broken from the root.
101E-****The % milling bur might be broken.
101F-****The % milling bur chucking has slipped out.
1020-****The % milling bur is too long.
1021-****The % milling bur is too short.
1022-****The % milling bur was not found.
1023-0000~1028-0000Milling data error.
1029-0000The spindle experienced an overload.
102A-0000The spindle experienced an overload.
102B-0000The spindle motor temperature is too high.
1034-0000The coolant tank is not installed.
1038-0000Milling data error. No milling bur is selected.
103A-000*DANGER!! The coolant is leaking!!
103B-0000The automatic correction is not yet finished.
103D-0000Milling data error. The milling bur cannot reach the milling position.
105E-0000The pressure of the compressed air is too high or low.
1062-0000An error occurred during the automatic correction.
1063-0000The milling cannot be started because the coolant has exceeded its expiration date.
****-****An unknown error occurred.
****-****
An unknown error occurred.
重新启动机器。
错误再次发生时
请联系本公司授权经销商或者本公司呼叫中心。
基本使用方法
加工方法
优化质量和效率
保养
故障排除方法
机器问题
加工品质问题
安装问题
对提示信息的处置方法
VPanel的错误信息
1000-****The % limit switch was not found.
1006-02**The % axis position has been shifted.
101C-0000The milling bur sensor was not found.
101D-00**The % milling bur cannot be released.
101D-01**The % milling bur cannot be released. It might be broken from the root.
101E-****The % milling bur might be broken.
101F-****The % milling bur chucking has slipped out.
1020-****The % milling bur is too long.
1021-****The % milling bur is too short.
1022-****The % milling bur was not found.
1023-0000~1028-0000Milling data error.
1029-0000The spindle experienced an overload.
102A-0000The spindle experienced an overload.
102B-0000The spindle motor temperature is too high.
1034-0000The coolant tank is not installed.
1038-0000Milling data error. No milling bur is selected.
103A-000*DANGER!! The coolant is leaking!!
103B-0000The automatic correction is not yet finished.
103D-0000Milling data error. The milling bur cannot reach the milling position.
105E-0000The pressure of the compressed air is too high or low.
1062-0000An error occurred during the automatic correction.
1063-0000The milling cannot be started because the coolant has exceeded its expiration date.
****-****An unknown error occurred.
Feedback
Was this information helpful?
1
2
3
4
5
NO
YES
Any additional feedback to help us improve.
Feedback
Thank you