Updater [ 2023-12-27, V240 ]

V240 Date: 2023/12/27
[bug fix] (Following problems have been fixed.)

1. During [collet open], "[EMERGENCY STOP]: 1018-0000 The chucking sensor was not found." may occur even if the machine is operating normally.

 

<Note>

- If you upgrade the firmware, you need to upgrade VPanel for DWX to V4.4.0 or later at the same time.

 

V230 Date: 2023/11/10
[bug fix] (Following problems have been fixed.)
1. The collet may not release the milling bar.

 

<Note>
- If you upgrade the firmware, you need to upgrade VPanel for DWX to V4.4.0 or later at the same time.

 

V220 Date: 2023/8/23
[change in spec.]
1. The origin detection process has been improved to avoid collisions of moving parts.
 

[bug fix] (Following problems have been fixed.)
1. When automatic correction is performed, an abnormal value may be set as the correction value.

 

<Note>
- If you upgrade the firmware, you need to upgrade VPanel for DWX to V4.4.0 or later at the same time.

 

V210 Date: 2023/6/12
[change in spec.]

1. [Manual correction] has been added to the [Machine Settings] > [Maintenance] tab in VPanel for DWX. 

- A manual correction function using milling has been added to improve milling quality.

 

<NOTE>

- VPanel for DWX V4.4.0 or later is required with the upgrade of the firmware version. 

 

V200 Date: 2023/4/5
[change in spec.]

1. The stability has been improved.

 

<Note>

- If you upgrade the firmware, you need to upgrade VPanel for DWX to v4.3.0 or later at the same time.

 

V190 Date: 2022/11/8
[change in spec.]
1. Operation at the time of limit switch detection for X/Y/Z axes has been improved, and detection accuracy will be maintained longer than before.

 

[bug fix] (Following problems have been fixed.)
1. Milling may not start when data is ouput from VPanel for DWX.

2. When a step-out is detected in each axis, an incorrect value is recorded in the log stored in the local file of the PC.

3. When an error 1020/1021-000*/1022-000* occurs, the contents of the log stored in the local file of the PC are not correct.

Note
- If you upgrade the firmware, you need to upgrade VPanel for DWX to v3.16.1 or later at the same time.

 

V180 Date: 2022/5/13
[bug fix] (Following problems have been fixed.)
1. An error may occur when automatic correction is performed with ZS-52D.

2. B-axis Rotary axis travel abgle has been extended from ±30° to ±30.5°.

Note
- If you upgrade the firmware, you need to upgrade VPanel for DWX to v3.16.1 or later at the same time.

 

V170 Date: 2022/1/28
[change in spec.]
1. New spindle unit: ZS-52D has been supported.  

2. Collet is now being kept open if the machine is not grasping a tool. 

3. Maintenance sequence has been changed. (Spindle run-in, Spindle replacement, Open collet, Close collet)

Note
- If you upgrade the firmware, you need to upgrade VPanel for DWX to v3.15.1 or later at the same time. 
 

V150 Date: 2021/7/9
[change in spec.]
1. In order to improve the accuracy of automatic correction, operation sequence has been changed. 
- Referential time for automatic correction has been changed from 10 minutes to 18 minutes.

Note
- You need to perform automatic correction with VPanel for DWX ver. 2.4.4 or later after upgrading the firmware. If you upgrade the firmware from V120 or earlier and then perform milling, [103B-0000] occurs and the message [The automatic correction is not yet finished.] is displayed even if automatic correction was performed.

V140 Date: 2020/5/14
[change in spec.]
1. Log is recorded at the time of the change of a milling bur now.

Note
- You need to perform automatic correction with VPanel for DWX ver. 2.4.4 or later after upgrading the firmware. If you upgrade the firmware from V120 or earlier and then perform milling, [103B-0000] occurs and the message [The automatic correction is not yet finished.] is displayed even if automatic correction was performed.

V130 Date: 2019/6/11
[change in spec.]
1. Air blower and external dust collector will not operate now when a tool is changed during the automatic correction.
2. The sequence of automatic correction has been reviewed, and the milling accuracy has been improved.
- You need to upgrade VPanel for DWX to V2.44 or later at the same time when you upgrade the firmware.
- You need to perform automatic correction with VPanel for DWX V2.44 or later after upgrading the firmware and VPanel for DWX.


V120 Date: 2018/2/1
[change in spec.]
Initial Release