V460 Date: 2025/6/18
[change in spec.]
1. A function has been added to determine the necessity of collet maintenance.
<NOTE>
- VPanel for DWX V4.12.0 or later is required with the upgrade of the firmware version.
V450 Date: 2025/4/18
[bug fix] (Following problems have been fixed.)
1. There is a bug in "L-axis aging operation".
<NOTE>
- VPanel for DWX V4.8.1 or later is required with the upgrade of the firmware version.
V440 Date: 2025/1/16
[bug fix] (Following problems have been fixed.)
1. The milling process may stop without any errors due to the filter cleaning signal from the dust collector (Renfert only).
2. A fatal error (104F-0201 The L axis position has been shifted.) may occur due to individual differences of the limit switch location.
<NOTE>
- VPanel for DWX V4.8.1 or later is required with the upgrade of the firmware version.
V430 Date: 2024/12/3
[bug fix] (Following problems have been fixed.)
1. The dummy pin cleaning starts with no dummy pin if the spindle is not holding the dummy pin.
<NOTE>
- VPanel for DWX V4.8.1 or later is required with the upgrade of the firmware version.
V420 Date: 2024/7/19
[change in spec.]
1. To improve the stability of correction/adjustment, the machine now confirms that the offset values are within the tolerance.
2. Added a function to detect error signals from the dust collector.
3. Improved the tool length detection to stabilize the operation.
[bug fix] (Following problems have been fixed.)
1. The work time of the tool is not counted if a fatal error occurs during milling.
<NOTE>
- VPanel for DWX V4.8.1 or later is required with the upgrade of the firmware version.
V410 Date: 2023/12/22
[bug fix] (Following problems have been fixed.)
1. During standby, if the touch sensor on the built-in panel is pressed and held while the clamp is not gripping the adapter in the milling area, the clamp moves to the starting position of milling at the back of the milling area without detecting the origin.
<NOTE>
- VPanel for DWX V4.4.0 or later is required with the upgrade of the firmware version.
V400 Date: 2023/10/31
[change in spec.]
1. The ambient temperature and humidity are now saved in logs only when the automatic correction is successfully completed.
[bug fix] (Following problems have been fixed.)
1. Air pressure errors may not be detected correctly.
<Note>
- If you upgrade the firmware, you need to upgrade VPanel for DWX to V4.4.0 or later at the same time.
V390 Date: 2023/8/23
[bug fix] (Following problems have been fixed.)
1. When automatic correction is performed, an abnormal value may be set as the correction value.
<NOTE>
- If you upgrade the firmware, you need to upgrade VPanel for DWX to V4.4.0 or later at the same time.
V380 Date: 2023/6/12
[change in spec.]
1. For dust collectors with interlocking functions, the dust collector force can now be set in VPanel for DWX under [Machine Settings] > [General] Tab > [Dust collector setting].
2. The default value of the dust collector"s vacume power is now set to [Low].
3. The rotary axis unit is now automatically cleaned after milling.
[bug fix] (Following problems have been fixed.)
1. Spindle errors may not be recorded in error log of VPanel for DWX.
2. If the connection to the machine is lost during maintenance, milling data may not be output.
<NOTE>
- VPanel for DWX V4.4.0 or later is required with the upgrade of the firmware version.
V370 Date: 2023/4/26
[change in spec.]
1. When the workpiece is moved to the View position during milling on the backside, the back surface of workpiece is turned upward, making it easier to check the milled surface.
[bug fix] (Following problems have been fixed.)
1. Errors may occur even when the dust collector is operating.
2. When one of the covers opens during spindle rotation, a fatal error may occur after an error [1017-000*] that allows operation to continue.
3. During limit detection of X axis, [102E-0000][The mechanical part has collided.] error may occur.
<NOTE>
- VPanel for DWX V4.3.0 or later is required with the upgrade of the firmware version.
V350 Date: 2023/3/13
[bug fix] (Following problems have been fixed.)
1. The tool does not move to the View position when initializing the machine"s status.
2. Error: 1031-0503 may occur when the machine is turned on.
<NOTE>
- VPanel for DWX V4.1.0 or later is required with the upgrade of the firmware version.
V340 Date: 2023/1/31
[change in spec.]
1. Time to start milling has been shortened.
2. The Z-axis ascent speed has been increased to shorten the tool return time.
<NOTE>
- VPanel for DWX V4.1.0 or later is required with the upgrade of the firmware version.
V330 Date: 2022/12/13
[change in spec.]
1. New dummy pins with flat tips has been supported.
- Old and new dummy pins can now be identified.
2. A dummy pin cleaning function has been added.
- Only new dummy pins is supported for cleaning.
<NOTE>
- VPanel for DWX V4.1.0 or later is required with the upgrade of the firmware version.
V320 Date: 2022/11/14
[change in spec.]
1. Accuracy of milling bar attachment/detachment operation has been improved.
[bug fix] (Following problems have been fixed.)
1. The disk stocker light may not turn yellow when an adapter ID is duplicated.
2. When [The milling bur cannot be released.] error occurs and [Forced tool release] is executed in VPanel for DWX, the milling bar may collide with the workpiece.
<NOTE>
- VPanel for DWX V4.1.0 or later is required with the upgrade of the firmware version.
V310 Date: 2022/9/7
[change in spec.]
1. Operation sequence has been improved and durability of the limit switch has been increased.
2. Operation sequence has been improved and durability of the tool sensor has been increased.
