Installing Plug-in for CorelDRAW
Installation Procedure
Install from the following link.
Supported Versions
For information regarding the latest supported versions, visit the Roland DG Corp. website (http://www.rolanddg.com/).
for Windows 
for Windows Install from the following link.
For information regarding the latest supported versions, visit the Roland DG Corp. website (http://www.rolanddg.com/).
What the GS-24 can be Used For
Step 4: Install the Blade Holder
Step 5: Perform a Cutting Test
Sending Data from Illustrator/CorelDRAW
Installing Plug-in for Illustrator
Outputting Data Created in Illustrator
Installing Plug-in for CorelDRAW
Preparations for Printing and Cutting (When Using CutStudio)
Printing and Cutting Procedure (CutStudio)
Step 1: Set the Printing and Cutting Areas
Step 2: Import the Sample Data
Step 3: Draw the Cutting Lines
Step 5: Load the Printed Material
Step 6: Set the Alignment Method (Sensor Mode)
Step 7: Perform Cutting (Sensor Mode)
Preparations for Printing and Cutting (When Using Illustrator)
Printing and Cutting Procedure (Illustrator)
Step 1: Set the Printing and Cutting Areas
Step 2: Position the Sample Data
Step 3: Draw the Cutting Lines
Step 5: Load the Printed Material
Step 6: Set the Alignment Method (Sensor Mode)
Step 7: Perform Cutting (Sensor Mode)
Preparations for Printing and Cutting (When Using CorelDRAW)
Printing and Cutting Procedure (CorelDRAW)
Step 1: Set the Printing and Cutting Areas
Step 2: Position the Sample Data
Step 3: Draw the Cutting Lines
Step 5: Load the Printed Material
Step 6: Set the Alignment Method (Sensor Mode)
Step 7: Perform Cutting (Sensor Mode)
Setting the Margins and the Distance between Crop Marks
Switching between 3 and 4 Crop Marks
Materials that can be Used for Printing & Cutting
Preparations for Printing and Cutting (Manual Mode)
Printing and Cutting Procedure (Manual Mode)
Step 1: Create Crop Mark Data Manually
Step 3: Load the Printed Material
Step 1: Perform Preparations for Cutting
Step 2: Create Perforated Line Data
Step 3: Set Perforated Cutting Conditions
Changing the Language Used for the Display
Initializing All Settings to Their Default Values
Checking the Machine Status (Self Test)
Changing the Contrast of the Display Screen
Moving the Cutting Carriage at High Speed
Cutting the Same Object Repetitively
Step 1: Prepare the Data for Recutting
Optimizing the Cutting Quality for the Material/Preventing Misaligned Cutting
Adjusting the Cutting-in Amount
Setting the Cutting Conditions
Setting Cutting Quality (QUALITY)
Setting the Amount of Offset for the Tip of the Blade (OFFSET)
Setting the Direction of the Coordinate Axis for Cutting (ROTATE)
Extending the Cutting Area (WIDTH EXTEND)
Setting the Speed of the Blade During Cutting (UPSPEED)
Cutting Detailed Characters and Complex Shapes
Cutting in the Same Position Repetitively (Overlap)
Cutting Corners Cleanly (Over Cut)
General Guide Regarding Cutting Conditions
Preventing and Correcting Misaligned Cutting
Using Thinner or Harder Material than Normal
Flat Material Cannot be Set Up using "PIECE" (Length is not Displayed)
Changing the Darkness of an Aligned Image
Illustrator Data Cannot be Imported
The Material Slips Away from the Pinch Rollers While Cutting
The Results of Cutting are Displaced when Using the Printing & Cutting Function
Uncut Areas Remain or Cut Edges are not Clean
The Machine Cuts the Carrier Paper
The Machine Cuts the Same Area Twice
Moving a Saved Symbol to a Different Computer
Checking Supported Versions of Illustrator/CorelDRAW
Software Cannot be Installed/Uninstalling Software
The Driver Cannot be Installed (Windows 7)
The Driver Cannot be Installed (Windows 8.1)
The Driver Cannot Be Installed (Windows 10)
Uninstalling the Driver (Windows 7)
Uninstalling the Driver (Windows 8.1)
Uninstalling the Driver (Windows 10)
Connecting Two or More GS-24 Units to a Single Computer (Connecting Multiple Units)
Copyright(C) 2015-2017. Roland DG Corporation All Rights Reserved.