再利用コンテンツ - note
Always unplug the power cord when attaching or removing parts and optional parts and when performing cleaning or maintenance that does not require the machine to be connected to a power source.
Attempting such operations while the machine is connected to a power source may result in injury or electrical shock.
Always unplug the power cord when attaching or removing parts and optional parts and when performing maintenance that does not require the machine to be connected to a power source.
Attempting such operations while the machine is connected to a power source may result in injury or electrical shock.
Keep children away from the machine.
The machine includes areas and components that pose a hazard to children and may result in injury, blindness, choking, or other serious accident.
Never attempt to disassemble, repair, or modify the machine.
Doing so may result in fire, electrical shock, or injury. Entrust repairs to a trained service technician.
Be sure to follow the operation procedures described in this machine's documentation. Never allow anyone unfamiliar with the usage or handling of the machine to touch it.
Incorrect usage or handling may lead to an accident.
Never operate the machine while tired or after ingesting alcohol or any medication.
Operation requires unimpaired judgment. Operating with impaired judgment may result in an accident.
Conduct operations in a clean, brightly lit location.
Working in a location that is dark or cluttered may lead to an accident, such as becoming caught in the machine as the result of an inadvertent stumble.
Never climb or lean on the machine.
The machine is not made to support a person. Climbing or leaning on the machine may dislodge components and cause a slip or fall, resulting in injury.
Caution: cutting tool.
This machine has a cutting tool. To avoid injury, handle the tool with care.
Never attempt operation while wearing a necktie, necklace, or loose clothing. Bind long hair securely.
Such items may become caught in the machine, resulting in injury.
Exercise caution to avoid being pinched or becoming caught.
Inadvertent contact with certain areas may cause the hand or fingers to be pinched or become caught. Use care when performing operations.
Be careful around the milling tool.
The milling tool is sharp. Broken milling tools are also dangerous. To avoid injury, exercise caution.
Never use a milling tool that has become dull. Perform frequent maintenance to keep the machine in good working order.
Inappropriate usage may result in fire or injury.
Never operate the machine if the cover is cracked or broken.
Doing so may result in injury. If the cover is cracked or broken, contact your authorized dealer.
Remove the milling tool before performing replacement work.
Contact with the blade may cause injury.
Caution: sharp components.
This machine contains areas that are sharp (Spacer table). To avoid injury, exercise caution.
Caution: sharp components.
This machine contains areas that are sharp. To avoid injury, exercise caution.
Be careful of the pointed portion inside the front cover.
There is a pointed portion inside the front cover. Exercise caution when cleaning.
Never attempt to disassemble, repair, or modify the AC adapter.
Doing so may result in fire, electrical shock, or injury. Entrust repairs to a trained service technician.
Keep the fingers and face away from the blower fan.
Fingers or hair may become entangled, resulting in injury.
Before switching on the power, check and ensure the safety of the surrounding area.
Make sure that movement of the machine poses no danger, including making sure no person is inside the machine's area of operation.
Wipe up any water around the main unit.
Failure to do so may cause a slip or fall, resulting in injury.
Use a dry cloth to clean the inside of the equipment.
Failure to do so may cause the components inside the equipment to degrade, which can lead to injury.
Connect to an electrical outlet that complies with this machine's ratings (for voltage, frequency, and current).
Incorrect voltage or insufficient current may cause fire or electrical shock.
Connect to an electrical outlet that complies with this machine's ratings (for voltage, frequency, and current). Also, be sure to set the voltage switch to match the voltage of the electrical outlet.
Incorrect voltage or insufficient current may cause fire or electrical shock.
If sparks, smoke, burning odors, unusual sounds, or abnormal operation occur, immediately unplug the power cord. Never use if any component is damaged.
Continuing to use the machine may result in fire, electrical shock, or injury. Contact your authorized Roland DG Corporation dealer.
If sparks, smoke, burning odors, unusual sounds, or abnormal operation occur, immediately unplug the power cord. Never use if any component is damaged.
Continuing to use the machine may result in fire, electrical shock, or injury. Contact Roland DG Corporation dealer.
Never use outside or in any location where exposure to water or high humidity may occur. Do not touch the power cord, plug, or electrical outlet with wet hands.
Doing so may result in fire or electrical shock.
Never allow any foreign object to get inside. Never expose the machine to liquid spills.
Inserting objects such as coins or matches or allowing beverages to be spilled into the ventilation ports may result in fire or electrical shock. If anything gets inside, immediately disconnect the power cord and contact your authorized dealer.
Never place any flammable object nearby. Never use a combustible aerosol spray nearby. Never use in any location where gases can accumulate.
Combustion or explosion could occur.
Handle the power cord, plug, and electrical outlet correctly and with care. Never use any article that is damaged.
Using a damaged article may result in fire or electrical shock.
When using an extension cord or power strip, use one that adequately satisfies the machine's ratings (for voltage, frequency, and current).
Use of multiple electrical loads on a single electrical outlet or of a lengthy extension cord may cause fire.
Position the machine so that the power plug is within immediate reach at all times.
This is to enable quick disconnection of the power plug in the event of an emergency. Install the machine next to an electrical outlet. Also, provide enough empty space to allow immediate access to the electrical outlet.
For accessories (optional and consumable items, power cord, and the like), use only genuine articles compatible with this machine.
Incompatible items may lead to an accident.
Never use the machine for any purpose for which it is not intended, or use the machine in an excessive manner that exceeds its capacity.
Doing so may result in injury or fire.
Do not use the supplied power cord for other products.
Do not use the supplied power cord and AC adapter with any other product.
If the machine will not be used for a long period, disconnect the power cord.
This prevents an accident caused by unexpected electric leakage or unintentional start of the machine.
Connect to ground.
This can prevent fire or electrical shock due to current leakage in the event of malfunction.
Connect to ground.
Failure to ground the machine may result in electrical shock when the machine is touched. Be sure to connect to ground.
Never use cutting oil.
This machine is not designed for the flow of cutting oil. Oil may get inside the machine and cause fire or electrical shock.
Never use a pneumatic blower.
This machine is not compatible with a pneumatic blower. Milling waste may get inside the machine and cause fire or electrical shock.
Never insert metal objects, flammable objects, or any other foreign object into interior areas other than the top of the table. Also, do not place water or other liquids on any area, including the table.
Doing so may cause an electrical short, resulting in electrical shock, or the inserted object may catch fire.
Do not use with any power supply other than the dedicated AC adapter.
Use with any other power supply may lead to fire or electrical shock.
 |
 |
 |
| Never place any object on top or subject to damage. | Never allow to get wet. | Never bend or twist with excessive force. |
 |
 |
 |
| Never make hot. | Never pull with excessive force. | Dust may cause fire. |
 |
||
| Never bundle, bind, or roll up. |
Do not block the air exhaust port.
Clogging the air exhaust port removes the escape route for the compressed air, which may lead to the internal lines rupturing. The internal lines rupturing may lead to coolant leaks and fire and electrical shock due to current leakage.
Handle the coolant filter carefully.
Dropping the filter or grasping it too strongly may damage the filter. If the filtration function does not work due to damage, the line may be clogged with milling waste, which may lead to coolant leaks and fire and electrical shock due to current leakage.
Use a dry cloth when cleaning silicone resin parts, and be careful to prevent the silicone resin from being damaged.
The silicone resin being damaged may lead to electric leakage.
Do not place any electronic devices in the vicinity of this machine.
Because coolant flows within this machine, water may be sprayed on objects in the vicinity of the machine when its front cover is opened. To prevent malfunctions, do not place any electronic devices in the vicinity of this machine.
Keep open flame away from the work area.
Ink and discharged fluid are flammable.
Ensure adequate ventilation for the work area.
Failing to perform ventilation may result in a health hazard or danger of combustion due to ink fumes.
Ensure adequate ventilation for the work area.
Failing to perform ventilation may result in a health hazard due to ink fumes.
- Any location exposed to open flame
- Any location where high temperature may occur
- Near bleach or any other such oxidizing agent or explosive material
- Any location within the reach of children
Fire may be a danger. Accidental ingestion by children may pose a health hazard.
- Any location where high temperature may occur
- Near bleach or any other such oxidizing agent or explosive material
- Any location within the reach of children
Accidental ingestion by children may pose a health hazard.
Never place an ink container (such as a cartridge or pouch) in fire.
Ink may flow out, catch fire, and spread fire to other nearby objects.
Never drink or sniff ink, cleaning liquid, or discharged fluid, or allow them to come in contact with the eyes or skin.
Doing so may be hazardous to your health.
Never drink or sniff the additives or coolant or allow them to come in contact with the eyes or skin.
Doing so may be hazardous to your health.
In the Event of Ingestion or Physical Distress
- In the event of contact with the eyes, immediately flush with water for at least 15 minutes. If eye irritation continues, seek treatment by a physician.
- In the event of contact with skin, immediately wash with soap. If irritation or inflammation occurs, seek treatment by a physician.
- In the event of ingestion, do not induce vomiting, and immediately seek treatment by a physician. Forcibly inducing vomiting may lead to danger of choking.
- If odor leads to physical distress, move to a well-ventilated location and rest quietly. If dizziness or nausea persists, seek treatment by a physician.
Never allow an ink container (such as a cartridge or pouch) to be subjected to impact, and never attempt to disassemble.
Ink may leak.
Refer to the appropriate safety data sheet (SDS) for the chemical substances used in the grease and the safety related to those substances.
Refer to the appropriate safety data sheet (SDS) for the chemical substances used in the additives and the safety related to those substances.
Refer to the appropriate safety data sheet (SDS) for the chemical substances used in the ink and the safety related to those substances.
After milling, wash away any products with purified water or the like.
After milling, there will be coolant on the product. Using the product as is may cause an inflammation or the like.
Entrust operations such as transportation, unloading, and emplacement to trained professionals.
Suitable equipment and technical skills are required in handling the machine. Tasks that require undue effort may result in a major accident.
Unloading and emplacement are operations that must be performed by the specified number of the workers or more as referring to the operation manual on the installation of the machine.
Tasks that require undue effort when performed by a small number of persons may result in physical injury. Also, if dropped, such items may cause injury.
Unloading and emplacement are operations that must be performed by 2 persons or more.
Tasks that require undue effort when performed by a small number of persons may result in physical injury. Also, if dropped, such items may cause injury.
Unloading and emplacement are operations that must be performed by *人（*インチモデルは*人） or more.
Tasks that require undue effort when performed by a small number of persons may result in physical injury. Also, if dropped, such items may cause injury.
Unloading and emplacement are operations that must be performed by *人（*インチモデルは*人、*インチモデルは*人） or more.
Tasks that require undue effort when performed by a small number of persons may result in physical injury. Also, if dropped, such items may cause injury.
Install the machine in a location that is level, stable, and able to bear the weight of the machine after checking the weight of the machine in the operation manual on the installation of the machine.
Installation in an unsuitable location may cause a major accident, including tip over, fall, or collapse.
Install the machine in a location that is level, stable, and able to bear the weight of the machine.
The total weight of the machine may reach 60 kg (132.28 lb.) or more. Installation in an unsuitable location may cause a major accident, including tip over, fall, or collapse.
Install the machine in a location that is level, stable, and able to bear the weight of the machine.
The total weight of the machine may reach *** kg（**インチモデルは*** kg） or more. Installation in an unsuitable location may cause a major accident, including tip over, fall, or collapse.
Install the machine in a location that is level, stable, and able to bear the weight of the machine.
The total weight of the machine may reach *** kg（**インチモデルは*** kg、**インチモデルは*** kg） or more. Installation in an unsuitable location may cause a major accident, including tip over, fall, or collapse.
Install in a level and stable location.
Failure to do so may result in falling of the machine, leading to injury.
Be sure to use the adjuster to secure the stand in place (in case the stand is equipped with an adjuster). Ensure that the adjuster is not loose.
If the machine should begin to topple, a major accident may result, including crushing of the parts of your body.
Be sure to lock the stand's casters.
If the machine should begin to topple, a major accident may result, including crushing of the parts of your body.
When loading or moving roll media, use lifting equipment, and exercise care to prevent falls.
Attempting to lift heavy media in a manner that taxes your strength may cause physical injury. Also, if dropped, such items may cause injury.
Handling roll media is an operation that must be performed by 2 persons or more, and care must be taken to prevent falls.
Attempting to lift heavy media in a manner that taxes your strength may cause physical injury. Also, if dropped, such items may cause injury.
When storing roll media, implement adequate safety measures to ensure that the stored media will not roll, fall, or topple over.
Danger exists of becoming pinned under the media and suffering serious injury.
High Temperature
Areas such as the dryer become hot. Exercise caution to avoid burns.
Remove any loaded media or switch off the sub power when printing is not being performed.
The continued application of heat at a single location may cause the release of toxic gases from the media or pose a fire hazard.
Never use media that cannot withstand heat.
Doing so may degrade the media, or may result in fire or the release of toxic gases.
Remove the object to be printed on or switch off the sub power when printing is not being performed.
The continued application of heat at a single location may cause fire or produce toxic gases.
High Temperature
The area around the UV-LED device becomes hot. Exercise caution to avoid burns.
Securely fasten the milling tool and workpiece in place. After securing in place, make sure no wrenches or other articles have inadvertently been left behind.
Otherwise, such articles may be thrown from the machine with force, posing a risk of injury.
Do not touch the spindle unit or the surrounding areas immediately after milling has ended.
Doing so may result in burns.
Never attempt operation while wearing a necktie, necklace, loose clothing, or gloves. Bind long hair securely.
Such items may become caught in the machine, resulting in injury.
Never attempt operation while wearing a necktie, necklace, or loose clothing. Bind long hair securely. When performing operations while wearing gloves, exercise sufficient caution to prevent entanglement in the machine.
Such items may become caught in the machine, resulting in injury.
Exercise caution to avoid being pinched or becoming caught.
Inadvertent contact with certain areas may cause the hand or fingers to be pinched or become caught. Use care when performing operations.
Never enter or place obstructions in the machine's operating area.
Doing so may result in your body becoming caught in the machine, or other such major accident.
When opening or closing the front cover, hold the part indicated in the following figure with both hands.
Failing to do so may result in your fingers being pinched, leading to injury.
Do not pull the adapter with excessive force when removing it.
Doing so may result in injury arising from your hand or arm hitting something.
Do not insert your hands or arms into the milling machine from the adapter magazine.
Doing so may result in injury arising from your hand or arm hitting something.
Do not use hot water for the coolant.
Using hot water may cause burns.
When raising or lowering the Coolant tank, hold the parts indicated in the following figure.
Failing to do so may result in your fingers being pinched, leading to injury.
Never attempt to mill magnesium or any other such flammable material.
Fire may occur during milling.
Never attempt to mill metal, carbon, or any other such conductive material.
Fire may occur during milling.
Keep open flame away from the work area.
Milling waste may ignite. Powdered material is extremely flammable, and even metal material may catch fire.
Keep open flame away from the work area.
Photo-curable resin may ignite.
When using a vacuum cleaner to take up milling waste, exercise caution to prevent fire or dust explosion.
Picking up fine cuttings using an ordinary vacuum cleaner may result in fire or explosion. Check with the manufacturer of the vacuum cleaner. When the safety of use cannot be determined, clean using a brush or the like, without using the vacuum cleaner.
Never use a vacuum cleaner to clean up milling waste.
Picking up fine cuttings using an ordinary vacuum cleaner may result in fire or explosion.
Wear dust goggles and a mask. Wash away any milling waste remaining on the hands.
Accidentally swallowing or inhaling milling waste may be hazardous to your health.
Wear dust goggles and a mask. Wash away any photo-curable resin remaining on the hands.
Accidentally swallowing or inhaling photo-curable resin may be hazardous to your health.
- Any location exposed to open flame
- Any location where high temperature may occur
- Near bleach or any other such oxidizing agent or explosive material
- Any location within the reach of children
Fire may be a danger. Accidental ingestion by children may pose a health hazard.
Never place photo-curable resin in fire.
Resin may flow out, catch fire, and spread fire to other nearby objects.
Never drink or sniff photo-curable resin, or allow it to come in contact with the eyes or skin.
Doing so may be hazardous to your health.
Ensure adequate ventilation for the work area.
Failing to perform ventilation may result in a health hazard due to fumes from the photo-curable resin.
Always close the lid securely when storing a photo-curable resin container. Failure to do so may result in photo-curable resin leakage.
Refer to the appropriate safety data sheet (SDS) for the chemical substances used in the photo-curable resin and the safety related to those substances.
Be sure to follow the operation procedures described in this documentation. Never allow anyone unfamiliar with the usage or handling of the machine to touch it.
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
This machine uses laser light, but dangerous laser radiation is not emitted outside the machine. It is safe to view the laser light through the window.
However, this may not be the case if the safety devices do not function due to issues such as them malfunctioning or a cover being damaged. Strictly follow the precautions given in this manual, and do not use this machine if you detect an error.
Do not use this machine if its safety devices do not function. Also, do not use this machine if the housing or window is cracked or deformed.
Doing so may lead to the external emission of laser light. Especially in the case of direct light but also in the case of diffused light, laser light that leaks outside of the machine may lead to serious eye injury or burns. This light may also ignite flammable objects, leading to fires.
Do not use this machine if its safety devices do not function. Also, do not use this machine if its protective covers are cracked or deformed.
Do not allow ultraviolet radiation emitted from the UV lamp to come into direct contact with your eyes or skin. Doing so may result in eye or skin injury.
Do not stare at post-exposure reflected light from a close distance for a long period of time.
Doing so may result in eye injury.
This machine is fitted with covers to keep external leakage of ultraviolet light at low levels, but incorrect handling or operation can lead to physical injury due to ultraviolet light. The extent of injury depends on the intensity and wavelength of the ultraviolet light, and the length of time of exposure. Prolonged exposure to strong ultraviolet light of hazardous wavelengths can cause injury to the eyes or skin. Exercise caution.
Ensure that the supplied compressed air is not contaminated by water, oil, chemicals, or foreign objects.
The components may deteriorate or rupture, or the contaminants may be scattered, posing a hazard.
Never use in a location exposed to cutting oil, solvents, chemicals, or other such substances.
Components may deteriorate or rupture under the pressure of compressed air.
Never use in a location exposed to direct sunlight.
Components may deteriorate or rupture under the pressure of compressed air.
Keep the temperature of the installation area within the specified range. Never place a stove or heater nearby.
Components may deteriorate or rupture under the pressure of compressed air.
Connect the air hose securely, so that it will not come loose.
A pressurized hose that comes loose may whip about uncontrolled, posing a hazard. Connect securely.
Before attempting to attach or detach the air hose or optional items or before attempting to perform cleaning or maintenance that does not require the machine to be connected to a power source, stop the supply of compressed air and allow the pressure to escape.
Allowing the equipment to remain under pressure poses a hazard of flying components.
Use an air hose of the specified diameter and having adequate pressure resistance.
Otherwise the article may come loose or rupture.
Keep the supply of compressed air within the specified pressure range.
Exceeding the specified pressure may result in rupture or other major accident.
Never strike or subject the object to impact.
Components may suffer damage or rupture under the pressure of compressed air.
When the machine will be out of use for a prolonged period, stop supply of compressed air and bleed off the air pressure.
This can prevent an accident.
Never damage the air hose, or bend or twist it with excessive force. Never use an item that has deteriorated.
A damaged air hose may rupture.
 |
 |
 |
 |
| Ensure that it is not crushed. | Make the cut edge straight. | Keep free from damage or soiling. |
Be sure to bleed off the air pressure before removing the regulator bowl.
Failure to do so may result in a rupture or components flying off.
Clean the regulator bowl using a neutral detergent. Never use solvents such as gasoline, alcohol, or thinner.
Using solvents may degrade the bowl and may result in a rupture.
Age limitation: Anyone aged 15 years or over
Never allow children under 15 to use this machine.
Restrain children from playing with the plastic bag used for packing.
Pulling the plastic bag over one's head or swallowing it may lead to suffocation.
Never keep the machine within children's reach to prevent them from inadvertently swallowing a small part, etc.
Never allow children to use this machine by themselves and keep it out of children's reach.
Never touch the head immediately after printing has finished.
Doing so may result in burns.
Never attempt to scan any object of high intrinsic or personal value, or that would otherwise be difficult to replace if damaged or broken.
Depending on conditions, the scan object may be damaged. Scan-object damage is not covered by warranty.
Securely fasten the object to be scanned to the table so that it does not slip or topple over.
The table rotates during scanning. Tipover or contact by the scan object may cause damage. Scan-object damage is not covered by warranty.
Never try to scan an object whose height is *** mm or more, or that protrudes beyond the table.
The object may strike the interior of the machine, causing breakdown or damage. The scan object may also be damaged. Scan-object damage is not covered by warranty.
Do not overfill or tilt the coolant tank.
The fluid inlet on the coolant tank is open. Overfilling or tilting will cause fluid to spill out.
Be sure to put the specified additive in the coolant tank.
Additives are effective in reducing coolant deterioration and raising the milling efficiency in order to maintain product performance. If additives are not used, the coolant may generate an unpleasant odor.
Be sure to set the voltage switch before you connect the power cable.
Failure to do so may result in fire or electrical shock. Also, malfunctions may result in an accident.
Perform this task with all power switches left switched off.
Otherwise sudden movement of the machine may cause injury.
This work must be performed before connecting the power cord.
The power turning on inadvertently during these operations may result in pinched hands or other injury.
Do not use with any electrical power supply that does not meet the ratings displayed on the AC adapter.
Use with any other power supply may lead to fire or electrical shock.
Never use any AC adapter or power cord other than those included with the machine.
Use with any other power supply may lead to fire or electrical shock.
Connect this machine to an electrical outlet. Never connect this machine directly to a power distribution panel or other such fixed wiring equipment.
Doing so increases the risk of fire or electrical shock.
Use a dry cloth when cleaning silicone resin parts, and be careful to prevent the silicone resin from being damaged.
The silicone resin being damaged may lead to electric leakage.
Do not place any electronic devices in the vicinity of this machine.
Because coolant flows within this machine, water may be sprayed on objects in the vicinity of the machine when its front cover is opened. To prevent malfunctions, do not place any electronic devices in the vicinity of this machine.
When lifting the machine, hold the locations shown in the figure.
Before lifting up the printer unit, check that the lifting bars do not rattle.
If the lifting bars rattle, retighten the bolts fixing them in place.
When not using the lifting bars, be sure to perform the work with *人.
Tasks that require undue effort when performed by a small number of persons may result in physical injury. Also, if dropped, such items may cause injury.
When not using the lifting bars, be sure to perform the work with *人（*インチモデルは*人）.
Tasks that require undue effort when performed by a small number of persons may result in physical injury. Also, if dropped, such items may cause injury.
When not using the lifting bars, be sure to perform the work with *人（*インチモデルは*人、*インチモデルは*人）.
Tasks that require undue effort when performed by a small number of persons may result in physical injury. Also, if dropped, such items may cause injury.
Be sure to set the shaft in a position that matches the outer diameter of the roll.
Setting the shaft in an incorrect position may result in injury caused by the roll falling off.
Be sure to attach the media flange and check that it is not loose.
If the media flange is not present, the roll may fall off.
Load the roll media correctly.
Otherwise the media may fall and cause injury.
The roll media is approximately * kg.
To avoid injury, handle the roll media with care.
The roll media is approximately * kg（*インチモデルは* kg）.
To avoid injury, handle the roll media with care.
The roll media is approximately * kg（*インチモデルは* kg、*インチモデルは* kg）.
To avoid injury, handle the roll media with care.
Never load media that weighs over * kg.
The machine may fail to withstand the weight and tip over or cause the media to fall.
Never load media that weighs over * kg（*インチモデルは* kg）.
The machine may fail to withstand the weight and tip over or cause the media to fall.
Never load media that weighs over * kg（*インチモデルは* kg、*インチモデルは* kg）.
The machine may fail to withstand the weight and tip over or cause the media to fall.
Be sure to perform this work with *人 or more. Have at least one person hold each of the four ends of the lifting bars and at least one person hold each end of the housing.
Tasks that require undue effort when performed by a small number of persons may result in physical injury. Also, if dropped, such items may cause injury.
Be sure to perform this work with *人（*インチモデルは*人） or more. Have at least one person hold each of the four ends of the lifting bars and at least one person hold each end of the housing.
Tasks that require undue effort when performed by a small number of persons may result in physical injury. Also, if dropped, such items may cause injury.
Be sure to perform this work with *人（*インチモデルは*人、*インチモデルは*人） or more. Have at least one person hold each of the four ends of the lifting bars and at least one person hold each end of the housing.
Tasks that require undue effort when performed by a small number of persons may result in physical injury. Also, if dropped, such items may cause injury.
Unpacking and installation must be carried out by 2 persons or more.
Failure to observe this instruction may cause the machine to fall over, resulting in injury.
Unpacking and installation must be carried out by *人（*インチモデルは*人） or more.
Failure to observe this instruction may cause the machine to fall over, resulting in injury.
Unpacking and installation must be carried out by *人（*インチモデルは*人、*インチモデルは*人） or more.
Failure to observe this instruction may cause the machine to fall over, resulting in injury.
Entrust operations such as transportation, unloading, and emplacement to trained professionals.
Suitable equipment and technical skills are required in handling the machine. Tasks that require undue effort may result in a major accident.
Install in a level and stable location.
Failure to do so may result in falling of the machine, leading to injury.
When moving the print-head carriage by hand, be sure to hold the specified position.
Moving it by holding positions other than those specified may deform and damage the cover.
Be sure to perform operations as specified by the instructions, and never touch any area not specified in the instructions.
Sudden movement of the machine may cause injury or burns.
Be sure to perform operations as specified by the instructions, and never touch any area not specified in the instructions.
Sudden movement of the machine may cause injury.
Do not hold places other than those instructed. Do not move the media by holding it directly.
Otherwise the media may fall off the media holder and cause injury.
Never touch the print-head carriage while output is in progress.
The print-head carriage moves at high speed. Coming into contact with the moving carriage may cause injury.
Do not touch the dancer roller needlessly.
The media take-up unit and feeder may move suddenly, which may result in injury.
Never insert your hand or fingers into the opening of the front cover.
The print head carriage moves at high speed inside the cover. Coming into contact with the moving carriage may cause injury.
Keep your hands and body away from the moving portions of the machine during operation.
Hands and other body parts can become caught in the machine, resulting in injury.
Do not insert your hands or other objects into the machine or look into the inside of the machine with the front cover open until the spindle has come to a complete stop.
If you open the front cover before the spindle comes to a complete stop, an emergency stop will occur. Due to inertia, the spindle continues rotating even after an emergency stop has occurred. It is dangerous to touch a rotating tool. Also, the coolant continues to flow until the spindle comes to a complete stop. Coming into contact with sprayed coolant may be hazardous to your health.
Never touch the tip of the knife.
Doing so may result in injury. The cutting performance of the blade will also be impaired.
Do not touch the tip of the separating knife.
Doing so may result in injury.
The probe tip is sharp. To avoid injury, handle it with care.
Be careful around the milling tool.
The milling tool is sharp. Broken milling tools are also dangerous. To avoid injury, exercise caution.
Be careful around the tip and other sharp edges.
Be careful not to touch the tool tip or any other sharp edges. Doing so may cause injury.
Under no circumstances should you move the Z-axis unit with your hands.
Doing so may cause a breakdown.
Be careful of the pointed portion inside the front cover.
There is a pointed portion inside the front cover. Exercise caution when cleaning.
Do not pull the adapter with excessive force when removing it.
Doing so may result in injury arising from your hand or arm hitting something.
High Temperature
The platen and dryer become hot. Exercise caution to avoid burns.
High Temperature
The dryer becomes hot. Exercise caution to avoid burns.
High Temperature
The milling tool and spindle motor become hot. Exercise caution to avoid fire or burns.
Never use the platen or dryer for any purpose for which they are not intended, such as to dry clothing.
Doing so may cause overheating, resulting in fire or accident.
Before attempting cleaning, switch off the sub power and wait until the platen and dryer cool (approximately 30 minutes).
Sudden movement of the machine may cause injury, or hot components may cause burns.
Before attempting cleaning, switch off the sub power and wait until the dryer cools (approximately 30 minutes).
Sudden movement of the machine may cause injury, or hot components may cause burns.
Remove any loaded media or switch off the sub power when printing is not being performed.
The continued application of heat at a single location may cause the release of toxic gases from the media or pose a fire hazard.
Never use media that cannot withstand heat.
Doing so may result in fire or the release of toxic gases or may degrade the media.
Never install this machine outside or in any location where exposure to water or high humidity may occur.
Current leakage may cause electrical shock or fire.
Never install the machine close to any flammable object or in a gas-filled location.
Combustion or explosion could occur.
Do not perform cleaning immediately after printing has finished. (Wait approximately 15 minutes after printing finishes.)
The area around the UV-LED device is hot and may cause burns.
To store discharged fluid temporarily, place it in the included drain bottle or in a durable sealed container such as a metal can or polyethylene tank, and cap the container tightly.
Any spillage or vapor leakage may cause fire, odor, or physical distress.
Switch off the power before performing the operations.
Fluid is discharged from the tube when the machine operates. In this situation, discharged fluid may spill onto your hands or the floor.
Before you detach the drain bottle, be sure to wait for the screen to display . After discarding the discharged fluid, promptly attach the drain bottle to the machine.
Failing to follow this procedure may cause discharged fluid to flow out of the tube and spill, soiling your hands or the floor.
Before you detach the drain bottle, be sure to wait for the screen to display . After discarding the discharged fluid, promptly attach the drain bottle to the machine.
Failing to follow this procedure may cause discharged fluid to flow out of the tube and spill, soiling your hands or the floor.
When is displayed, you must discard the discharged fluid.
If you do not discard it at this stage, discharged fluid will overflow from the drain bottle during the procedure that follows.
When appears on the screen, be sure to discard the discharged fluid.
Failing to discard the discharged fluid when is displayed will lead to the discharged fluid overflowing during cleaning.
When the message appears on the screen, discard as much of the discharged fluid as possible.
Repeatedly selecting without discarding the discharged fluid may cause it to spill out of the drain bottle, soiling your hands or the floor.
When the message appears on the screen, discard as much of the discharged fluid as possible.
Repeatedly selecting without discarding the discharged fluid may cause it to spill out of the drain bottle, soiling your hands or the floor.
Never place discharged fluid or ink near an open flame.
Doing so may cause a fire.
Be sure to discard the discharged fluid at this stage.
If you do not discard it at this stage, discharged fluid will overflow from the drain bottle during the procedure that follows.
Be sure to discard the discharged fluid at this stage.
A large amount of ink will be discharged during this operation. The discharged fluid must be discarded at this stage. If you do not discard it at this stage, discharged fluid may overflow from the drain bottle during the procedure that follows.
Be sure to turn on the dust collector.
Milling waste and workpieces are flammable and toxic.
Never use gasoline, alcohol, thinner, or any other flammable material.
Doing so may cause a fire.
Never use gasoline, thinner, or any other flammable material.
Doing so may cause a fire.
Never use a solvent such as gasoline, alcohol, or thinner to perform cleaning.
Doing so may cause a fire.
When handling resin, wear rubber gloves and protective eyewear.
Do not allow resin to come into contact with the skin or eyes.
When handling resin and ethanol, wear rubber gloves and protective eyewear.
Do not allow resin or ethanol to come into contact with the skin or eyes.
Always close the lid securely when storing photo-curable resin in a container.
Failure to do so may result in photo-curable resin leakage. The remaining resin may also deteriorate or cure, making it impossible to use.
Never install in a location exposed to open flame.
Milling waste may ignite. Powdered material is extremely flammable, and even metal material may catch fire.
Be sure to use the specified additive.
Additives are effective in reducing coolant deterioration and raising the milling efficiency in order to maintain product performance. Furthermore, if additives are not used, the coolant may generate an unpleasant odor.
After milling, wash away any products with purified water or the like.
After milling, there will be coolant on the product. Using the product as is may cause an inflammation or the like.
Handle the coolant filter carefully.
Dropping the filter or grasping it too strongly may damage the filter. If the filtration function does not work due to damage, the coolant line may be clogged with milling waste, which may lead to coolant leaks and fire and electrical shock due to current leakage.
Be sure to use the specified chelating reagent.
The chelating reagent works to make calcium and similar substances contained in the water inactive, making it easier to clean off milling powder that adheres to the machine and the cutting tool after milling.
Be careful around milling waste.
Sharp milling waste may become mixed. To avoid injury, exercise caution.
Rotate the collet replacement jig with the collet tap inserted.
If the collet replacement jig is rotated without the collet tap inserted, the collet may be damaged.
During repairs, part replacements, and similar work, never perform any operations that are not written in the user's manual. Be sure to contact your authorized dealer.
Securely insert the air hose as far as it will go. Lightly tug the hose to make sure it does not come loose.
If it is not inserted securely, it may come loose.
Supply the compressed air after the air hose is connected securely.
Failure to do so may cause an accident.
Before removing or attaching the regulator and before performing maintenance, make sure that the bowl is securely attached.
If the bowl is not properly attached, it may come flying off when compressed air is supplied.
Turn the air pressure adjustment knob slowly and carefully.
Otherwise, the machine may move suddenly, posing a risk of injury.
The pressure of the compressed air must be 1.0 MPa or less.
Anything higher may result in a serious accident such as a rupture.
Before supplying compressed air, make sure that the bowl is securely attached.
If the bowl is not properly attached, it may come flying off.
Securely fasten the object to be scanned to the table.
The table will move. Failure to fasten the object to be scanned may result in it falling over and being damaged.
Set the object to be scanned within the predetermined range.
Failure to do so may result in the object to be scanned being damaged.
Be sure to remove the probe cover before scanning.
Failure to do so may result in the object to be scanned being damaged by coming in contact with the probe cover.
Switch off the machine's power switch and remove the power cord from the machine before performing maintenance operations.
Attempting such operations while the machine is connected to a power source may result in injury or electrical shock.
Do not inadvertently touch the computer or the operating panel while performing this task.
Unintended operation of the machine may lead to you being caught in the machine.
This procedure makes the machine operate.
Before you perform this procedure, check to make sure that operation of the machine will not create any hazard or danger.
Leave this work to a suitably qualified worker.
This procedure includes work near sources of electrical danger and complex assembly work. Incorrect work may result in injury and mechanical malfunction.
Install the machine in a clean, brightly lit location.
Working in a location that is dark or cluttered may lead to an accident, such as becoming caught in the machine as the result of an inadvertent stumble.
Do not set duplicate IDs.
Simultaneously connecting multiple machines with the same ID may lead to the computer shutting down or it being impossible to install the driver.
Do not place your hands on or touch the flat table or inside the machine (except for the cartridge slots).
Doing so may cause burns.
Do not place any object on top of the plate or press on it with force.
Doing so may cause damage.
Do not place any objects in front of or behind the flat table.
The flat table moves horizontally and vertically. If there is an object between the flat table and the machine, it can be caught and cause the machine to malfunction.
If anything drops toward the back of the flat table, turn off all power switches before looking for the dropped object.
Otherwise sudden movement of the machine may cause injury.
When using anhydrous ethanol or isopropyl alcohol, be sure to follow the product's usage precautions.
Exercise caution regarding items such as fire, ventilation, and rashes.
Only use anhydrous ethanol or isopropyl alcohol.
Using chemicals (or similar substances) other than anhydrous ethanol or isopropyl alcohol may lead to UV-LED device damage.
Use cloth that is not fluffy to wipe off the parts. Do not use a hard material such as metal.
Using cloth that is fluffy or a hard material such as metal may lead to UV-LED device damage.
Be sure to perform operations as specified by the instructions, and never touch any area not specified in the instructions.
Otherwise sudden movement of the machine may cause injury.
Do not place any objects on top of the extension plate or press on it with force.
Doing so may cause damage.
Caution: sharp components.
Take care to avoid injuries arising from touching the edges of the spacer table and other such sharp components.
Be sure to turn off all the power switches in this situation.
Failure to observe this instruction may cause the machine to move suddenly, resulting in injury.
Before attempting cleaning, switch off the sub power and wait until the UV-LED device cools (approximately 15 minutes).
Sudden movement of the machine may cause injury, or hot components may cause burns.
Never touch the cutting carriage while output is in progress.
The cutting carriage moves at high speed. Coming into contact with the moving carriage may cause injury.
Never touch the cutting carriage while measurement is in progress.
The cutting carriage moves at high speed. Coming into contact with the moving carriage may cause injury.
Do not open the lid on the drain cartridge.
Any spillage or vapor leakage may cause fire, odor, or physical distress.
Before you remove the drain cartridge, wait for a message to be displayed in the utility.
Failing to follow this procedure may cause discharged fluid to flow out of the tube and spill, soiling your hands or the floor.
The pinch rollers cannot be moved directly by hand. Move them with the media guide.
Attempting to forcibly move these rollers may result in injury.
Never place the drain cartridge or ink near an open flame.
Doing so may cause a fire.
Never operate the machine if the cover is cracked or broken.
Doing so may result in injury. If the cover is cracked or broken, contact your authorized Roland DG Corporation dealer.
Never allow any foreign object to get inside. Never expose the machine to liquid spills.
Inserting objects such as coins or matches or allowing beverages to be spilled into the ventilation ports may result in fire or electrical shock. If anything gets inside, immediately disconnect the power cord and contact your authorized Roland DG Corporation dealer.
Never attempt to mill magnesium, titanium, or any other such flammable material.
Fire may occur during milling.
Conduct operations in a clean, brightly lit location.
Working in a location that is dark or cluttered may lead to an accident, such as being injured by the machine falling over as the result of an inadvertent stumble.
Only use anhydrous ethanol or isopropyl alcohol.
Using chemicals (or similar substances) other than anhydrous ethanol or isopropyl alcohol may lead to operation panel damage.
Have two or more people available when removing (handling) the taken up media.
Otherwise the media may fall and cause injury.
High Temperature
Areas such as the heater become hot. Exercise caution to avoid burns.
When handling ink and ethanol, wear rubber gloves and protective eyewear.
Do not allow ink or ethanol to come into contact with the skin or eyes.
Before you detach the drain bottle, be sure to wait for the screen to display . After discarding the discharged fluid, promptly attach the drain bottle to the machine.
Failing to follow this procedure may cause discharged fluid to flow out of the tube and spill, soiling your hands or the floor.
Never allow any foreign object to get inside. Never place liquids on the machine or expose it to liquid spills.
Inserting objects such as coins or matches or allowing beverages to be spilled into the ventilation ports may result in fire or electrical shock. If anything gets inside, immediately disconnect the power cord and contact your authorized dealer.
When interrupting the power supply of the machine, disconnect three power plugs: one on the main unit and two on the dryer.
Failure to do so may result in electrical shock or accidents attributable to malfunctions.
High Temperature
The areas inside the dryer, under the dryer, and near the extension apron become hot. Exercise caution to avoid burns.
Refer to the appropriate safety data sheet (SDS) for the following items related to the ink, cleaning liquid.
- Hazards of the included chemical substances
- Handling
- Emergency measures when these toxic substances get on the skin or in the eyes
https://www.rolanddg.com/en/about-us/sustainability/safety-data-sheet
Do not allow light from the UV lamp to come into direct contact with your eyes or skin. Light initially emitted from the UV lamp may be reflected and small amounts of light may leak through gaps in the machine. Do not stare at these kinds of light or allow them to come into contact with your skin for long periods of time.
Doing so may result in eye or skin injury.
Never operate the machine if the cover is cracked or broken.
If the cover is cracked or broken, contact your authorized dealer.
To prevent damage to the device and electrical shock, only insert and remove the rotation shaft unit connector when the main power is off or when executing [Insert/remove optional unit] from the printer's operation panel.
Exercise caution to prevent the rotation shaft unit from falling.
Failure to do so may result in injury.
When opening or closing the front cover, hold the parts indicated in the following figure with both hands.
Failing to do so may result in your fingers being pinched, leading to injury.
To prevent damage to the device and electrical shock, only insert and remove the rotation shaft unit connector when the main power is off or when executing [Insert/remove optional unit] from the utility.